Login:
Stimmen - 5, Durchschnittliche Bewertung: 3.4 ( )

Anleitung Carrier, modell AAW-22CM1FHUE

Hersteller: Carrier
Dateigröße: 5.16 mb
Dateiname:
Unterrichtssprache:enes
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


7).Install the two leveling screws into the 90 support brackets. Test the bracket assembly in the window before cabinet installation. If the leveling screws are distanced too far away from the wall to provide stability, it may be necessary for you to fill this area with a solid piece of wood. See (Fig. 8). B. Measure the inside window sill width and find the center as shown in (Fig. 6). Align the V-slot in each bracket on these marks and mount the brackets to the sill using 3/4" screws provided. Brackets should be perpendicular to the inside window sill. See (Fig. 6). C. For proper condensation run-off it will be necessary to adjust the angle/pitch of the window brackets. This is accomplished by adjusting the distance of the leveling screw on the outer wall. The maximum angle/pitch should not exceed more than 3/16". See (Fig.7). D. Cut the seal strip to fit the underside of the bottom window sash. Remove the peel-off backing on the seal and attach it to this sash. See (Fig. 9). (TOP VIEW) Bracket Assembly Bracket Bolts Leveling Screw 90 Angle Support Brackets Fig. 5 Center Window sill V-slot Fig. 6 Measurement for Model 10K =9.6" Measurement for Model 12K = 10.3" Measurement for Model 15K to 24K = 12.6" Measurement for Model 8K = 7.5" 7.5" 12.6" 12.6" 7.5" (2) 3/4" screws per bracket Bracket Assembly Leveling Screw Outer Wall Construction 3/16" Maximum Fig. 7 Solid Piece Wood (If required) Fig. 8 CAUTION! ! Use a solid piece of wood to provide stability. This will be required when sills are extra deep. See (Fig. 8). Window Sash Window Sash Sealing Strip Fig. 9 10 6. Installation of the cabinet B. Ensure the "L" shaped mounting channel is positioned in front of the sash. The "U" shaped bottom channel of the cabinet should be positioned in the track provided on the bracket assembly. Pull the window down until it rests just behind the front of the "L" shaped mounting channel. See (Fig. 11). A. Align one hole in the bottom of the cabinet with one hole in the bracket assembly. Secure the cabinet to the bracket using (3) 1/4" screws provided. Repeat the same procedure on the opposite side of the cabinet. See (Fig. 10). C. Check to make sure that the cabinet is slanted slightly downward on the outside. If necessary, re-adjust support bracket as shown in (Fig. 7). Fig. 10 1/4" Screws Fig. 11 7. Secure Shutters A. Carefully slide the air conditioner back into the cabinet.(Please seek assistance for this procedure). B. Reinstall the slide-out-chassis security screws (removed earlier) on both sides of the cabinet. See (Fig. 12). Secure the top of the frames to the window sash with (2) 3/4" screws. C. Now, secure bottom frame of shutters using one shutter clamp and one 3/4" screw on each side(Fig. 12). 8. Reinstalling Front Panel Assembly A. Position the front panel on the cabinet starting at the top. The front panel lock tabs must be inserted into the retaining slots in the cabinet. Repeat this procedure on all sides. B. Secure the front grille to the cabin...

Dieses Handbuch ist für folgende Modelle:
Splitgeräte - AAW-08CM1FHUE (5.16 mb)
Splitgeräte - AAW-22CR1FHUE (5.16 mb)
Splitgeräte - AAW-24CM1FHUE (5.16 mb)
Splitgeräte - AAW-24CR1FHUE (5.16 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien