Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Admiral Dateigröße: 5.16 mb Dateiname: 951efc58-cf42-40d8-9063-5a4a9b7d819b.pdf Unterrichtssprache:

" L" Shaped Top Channel: Stick the double adhering seal to the " L" shaped top channel, and then Install the "L" shaped top channel to the cabinet as shown in (Fig. 3) using (5) 1/4" screws. B. "n" Shaped Bottom Channel installed as shown in (Fig. 3)using (4) 1/4" screws. NOTE: For 15K to 24K models, the bottom channel has been factory- installed, and their shapes may differ from the others,but their functions are similar. 4. Assembly of the side shutters (curtains) to the cabinet. Slide the shutters into the top and bottom channels as shown in (Fig. 4). The shutters are identified (on each frame) as "left" & "right". Attach the shutters to the cabinet using (4) 1/4" screws on each side. Double Adhering seal For 15K to 24K models (Factory-installed). F HR FAN SPEED MODEOFFON/ TIMER Airconditioner WAIT THREE MINUTES BEFORE RESTARTING Coil Pull Handle Chassis 9 INSTALLATION INSTRUCTIONS WAC 8-24 USER MAN FINAL 3/2/05 12:13 PM Page 11 WAC 8-24 USER MAN FINAL 3/2/05 12:13 PM Page 12 INSTALLATION INSTRUCTIONS 5. Installation of Mounting Brackets and First Sealing Strip V-slot NOTE: Windows come in a variety of different styles. Therefore, it may be necessary to modify or improve your particular installation. A. Attach the bracket assembly to 90 angle support brackets (Fig. 5) using (2) 1 1/2" bolts Two bolts per bracket. Secure with the (2) 1/4" lock washers and (2) 1/4"nuts. DO NOT immediately tighten these bolts as it may be necessary to adjust the depth of the bracket assembly, depending on the depth of your window sill. See (Fig. 7).Install the two leveling screws into the 90 support brackets. Test the bracket assembly in the window before cabinet installation. If the leveling screws are distanced too far away from the wall to provide stability, it may be necessary for you to fill this area with a solid piece of wood. See (Fig. 8). B. Measure the inside window sill width and find the center as shown in (Fig. 6). Align the V-slot in each bracket on these marks and mount the brackets to the sill using 3/4" screws provided. Brackets should be perpendicular to the inside window sill. See (Fig. 6). C. For proper condensation run-off it will be necessary to adjust the angle/pitch of the window brackets. This is accomplished by adjusting the distance of the leveling screw on the outer wall. The maximum angle/pitch should not exceed more than 3/16". See (Fig.7). D. Cut the seal strip to fit the underside of the bottom window sash. Remove the peel-off backing on the seal and attach it to this sash. See (Fig. 9). (TOP VIEW) Bracket Assembly Bracket Bolts Leveling Screw 90 Angle Support Brackets Fig. 5 Center Window sill V-slot Fig. 6 Measurement for Model 10K =9.6" Measurement for Model 12K = 10.3" Measurement for Model 15K to 24K = 12.6" Measurement for Model 8K = 7.5" 7.5" 12.6" 12.6" 7.5" (2) 3/4" screws per bracket Bracket Assembly Leveling Screw Outer Wall Construction 3/16" Maximum Fig. 7 Solid Piece Wood (If required) Fig. 8 CAUTION! ! Use a solid pi...

Herunterladen

Geben Sie zwei Ziffern: