Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Bloomfield Dateigröße: 1.66 mb Dateiname: Unterrichtssprache:

Install a new seat cup, making sure the knob on the stem is fully inserted into the pocket of the seat cup, and the skirt of the seat cup is fully inserted into the bonnet. 15 SERVICING INSTRUCTIONS (continued) SERVICING INSTRUCTIONS (continued) CAUTION CHEMICAL BURN HAZARD Deliming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spill, splash or pour water or deliming solution into or over any internal component other than the inside of the water tank. IMPORTANT: DO NOT allow any internal components to come into contact with the deliming solution. Take care to keep all internal components dry. NOTE: Repeat steps 4 thru 5 as required to remove all scale and lime build-up. PROCEDURE: Delime the Water Tank PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: As required (Brewer slow to heat) TOOLS: Deliming Solution Protective Gloves, Goggles & Apron Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush Large Sink (or other appropriate work area) 1. Disconnect brewer from the electrical supply. Turn off the water shut-off valve and disconnect the water supply line from the brewer inlet fitting. 2. Remove the tank lid assembly as described on page 13. 3. Remove the water tank from the brewer body by lifting straight up. Empty all water from the tank. Set the tank back into the brewer. 4. Mix 2 quarts of deliming solution according to the manufacturer’s directions. Carefully pour the deliming solution into the water tank. Lower the lid assembly back onto the tank. Allow to sit for 30 minutes, or as directed by the manufacturer. 5. At end of soaking period, remove lid assembly from tank. Thoroughly rinse internal components of lid assembly with clear water. Using a stiff bristle brush, scrub the heating element (and faucet water coil on automatic brewers) to remove lime and calcium build-up. Rinse with clean water. Store lid assembly in a safe location . 6. Remove the tank from the brewer and empty. Using a stiff bristle brush, scrub the interior of the water tank to remove lime and calcium build-up. Rinse with clean water. 16 SERVICING INSTRUCTIONS (continued) SERVICING INSTRUCTIONS (continued) 7. Set the tank back into the brewer. Reassemble the tank lid to NOTE: Normally, silicone the water tank. Make sure the gasket is properly in place, hoses do not need to be then reinstall the hold-down strap. delimed. Should deliming hoses become necessary, 8. Reinstall wiring to heating element and thermostat. Reinstall Bloomfield recommends the hi-limit thermostat (if removed). For brewers with hot replacing the hoses. water faucet, reassemble faucet piping. Verify that all internal components are dry, then reinstall the top panel. 10. Reconnect brewer to electrical supply and, for automatic brewers, reconnect water supply. 11. Install the brew chamber without filter paper or grounds. Run at least three full brew cycles and discard all water generated. 12. Brewer is ready to use. 17 EXPLODED VIEW & PARTS LIST CABINET & RELATED COMPONENTS 18 EXPLODED VIEW & PARTS LIST (continued) EXPLODED VIEW & PARTS LIST (continued) ITEM PART NO. DESCRIPTION USED ON 1 8700-16 Warmer Cover Plate, Black All 8875-149 Warmer Cover Plate, Brown All 4 8543-80 Clip, Panel Retaining All 20 8543-23 Tinnerman Nut, #8 (not shown) All 23 8543-69 Heyco Bushing All 33 8543-42 Spray Head Gasket All 34 82727 Spray Disk All 34a 8543-45 Spray Head Retainer All 35 8572-34 Door, Solenoid Access (Old-Style) 8540, 8541, 8572, 8573 & 8574 85089 Door, Solenoid (New-Style) 8540, 8541, 8572, 8573 & 8574 38 8574-10 Cover, Electric 8574 47 8810-12 Button Plug (Non-faucet) 8541, 8542, 8543, 8571, & 8573 47a 8033-60 Button Plug (Hi-Limit) 8574 48 8033-55 Leveler, Adjustable Leg All 8033-56 Cap, Adjustable Leg All 81732 Adjustable Leg Assembly All 70 8706-75 Button Plug (Timer) 8540, 8541, 8572, 8573 & 8574 101 8572-13 Top Assembly All 102 8512-56 Basin Cover Assy (w / Warmer) 8540, 8541, 8543 8542-6 Basin Cover Assy (no Warmer) 8542, 8571, 8572, 8573 & 8574 103 8543-46 Reservoir Cover All 104 8543-49 Reservoir Cover Hinge Wire All 108 8541-21 Basin Pan (Automatic) 8540, 8541, 8572, 8573 & 8574 8543-29 Basin Pan (Pour-Over) 8542, 8543, 8571 110 8542-110 Basin Front Label 8542 8543-160 Basin Front Label 8543 8541-160 Basin Front Label 8540 & 8541 8572-110 Basin Front Label 8572, 8573 & 8574 8571-20 Basin Front Label 8571 111 8542-25 Bottom Assembly (In-Line Pour-Over) 8542 & 8543 8540-25 Bottom Assembly (In-Line Automatic) 8540 & 8541 8571-13 Bottom Assy (3-Station Pour-Over) 8571 8572-33 Bottom Assy (3-Station Automatic) 8572 & 8573 Bottom Assy (3-Station Automatic) 8574 112 8541-155 Panel, Front 8540 & 8541 8543-48 Panel. Front 8542 & 8543 8571-3 Panel, Front 8571 8572-10 Panel, Front 8572, 8573 & 8574 114 8718-61...

Herunterladen

Geben Sie zwei Ziffern: