Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
3. Insert other rod into front hole on right side of firebox and fasten using remaining shoulder screw. Rear Hole Figure 16 - Installing Fireplace Screen (Shown Without Fireplace Hood for Clarity) ................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Rod Front Hole Ring Screen Screw FIREBOX INSTALLATION USING OPTIONAL ACCESSORY MANTELS This firebox may be installed using the corner or cabinet mantel with hearth base accessories against a wall in your home. You must use a GA6090 brass trim kit included with the mantel accessories (see Accessories, pages 12 and 13). Follow the instructions below to install the firebox in this manner. Note:The instructions below show installation using GM100F/GM101U/GM102W/ GM106F/GM107U series cabinet mantels and the G3000F/G3001U/G3004W/G3006F/ G3007U series hearth base accessories. The hearth base accessory shown is optional for this installation. You can install firebox and cabinet mantel directly on the floor. The corner mantel cannot be installed with the G3000F/G3001U/G3004W/G3006F/ G3007U series hearth base. You must install corner and face mantels directly on the floor. If mounting firebox and cabinet mantel to the floor or using corner mantel, an optional G3005 Slim Base kit may be installed. 1. Assemble cabinet mantel, hearth base, brass trim, and trim accessories. Assembly instructions are included with each accessory. 2. If using an optional GA3700 blower (FB32CA and NLFB32C models only), install a properly grounded, 120 volt three-prong electrical outlet at firebox location if an outlet is not there. If possible, locate outlet so cabinet mantel will cover it when installed (see Figure 18). 3. Install gas piping to firebox location. This installation includes an approved flexible gas line (if allowed by local codes) and a manual shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Connecting to Gas Supply in your log set owner’s manual. NOTICE: A qualified service person must connect firebox to gas supply. Follow all local codes. Electrical Gas Line Outlet Access Figure 17 - Placing Hearth Base Accessory Against Wall .................... QQQQQQQQQQ .......... Hearth Base Flexible Gas Line Hole Cabinet Mantel ........................................ QQQQQQQQQQQQQQQQQQQQ .................... .................... QQQQQQQQQQ .......... Figure 18 - Installing Cabinet Mantel For more information, visit 10 OWNER’S MANUAL INSTALLATION Continued 4. Place hearth base accessory against wall at installation location. Cut an access hole in hearth top to run flexible gas line to firebox (see Figure 17, page 10). Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You can secure base to floor using wood screws. Countersink screw heads and putty over. 5. Route flexible gas line through access hole in hearth base. 6. Center cabinet mantel on hearth base (see Figure 18, page 10). Make sure mantel is flush against wall. 7. Break off nailing flanges (see Figure 19) with hammer or pliers. IMPORTANT: When installing Brass Trim Kit, see instructions included with mantel accessory. 8. Place cardboard or other protective material on top of hearth base. Carefully set firebox on protective material, with back of firebox inside mantel opening. 9. Attach flexible gas line to log set. See Connecting to Gas Supply in your log set owner’s manual. 10. If installing GA3700 blower (FB32CA and NLFB32C models only), route blower electrical cord through bushing included with blower accessory in right side firebox support and bushing in side access opening of firebox. Plug electrical cord into electrical outlet. See Installing Blower Accessory, page 8. Nailing Flanges Figure 19 - Location of Nailing Flanges 11. Carefully insert firebox into cabinet mantel. Be careful not to scratch or damage hearth base, cabinet mantel, or any laminate trim on hearth base. Remove prote...
Dieses Handbuch ist für folgende Modelle:elektrische Heizungen - NLFB32NC (532.8 kb)