Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Vanguard Managed Solutions Dateigröße: 532.8 kb Dateiname: Unterrichtssprache:

Route power cord through both plastic bushings and plug the power cord into a 3prong grounded wall receptacle near the firebox. b. If your firebox installation is recessed and/or pre-wired, see Built- In Installation of Blower Accessory, column 2. 8. Turn on power to duplex outlet if previously turned off per the warning in step 1. 9. Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation. WARNING: Never touch the blower wheel while in operation. 10. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front of the blower. 11. Replace bottom of firebox. Note:Make sure the back of the firebox bottom slides under the rear of the firebrick (lift the firebrick up if necessary.) 12. Reattach firebox bottom using 4 screws removed in step 1. Note:Discard the remaining hardware items. 13. Install the log set heater according to the installation instructions supplied with the heater. NOTICE: A qualified electrician must connect electrical wiring to duplex outlet for built-in installation. Follow all local codes. In absence of local codes followThe National Electrical Code ANS/ NFPA 70. Control Knob Control Speed Shaft Control Lock Nut Figure 10 - Attaching Speed Control Plastic Bushing Figure 11 - Installing Plastic Bushing for Power Cord Built-In Installation of Blower Accessory 1. Before replacing bottom of firebox, remove screw holding duplex outlet to the support bracket in the bottom of firebox. Remove duplex outlet. 2. Clamp electrical cable into firebox through smallest hole in outer casing using strain relief provided. 3. Route wires from electrical box through hole in side of heater and hole in support bracket (see Figure 12). 4. Connect wires from the electrical box to duplex outlet. Match wire colors to those indicated on duplex outlet. Be sure to connect ground wire. 5. Replace duplex outlet with screw. 6. Plug blower power cord into duplex outlet. 7. Replace bottom of firebox. Cables From Support Electrical Bracket Blower Duplex Outlet Figure 12 - Routing Blower Accessory Power Cord for Built-In Installation Source Screw Blower Power Cord Operating the Blower Light your gas appliance with the blower off. After about 15 minutes, turn the blower on to deliver heated air at the top louvers. The blower features a variable control which allows you to select the speed you desire. Note:Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions. INSTALLING LOG HEATER IN FIREBOX CAUTION: Do not remove the metal data plates attached to the heater base assembly. The data plates contain important warranty information. CAUTION: Do not pick up log base assembly by burners. This could damage burners. Only handle base by grates. 1. Remove four screws holding firebox bottom in place. 2. Lift and remove firebox bottom (see Figure 13, page 10). 3. If installing GA3700 Blower Accessory (Models FB32CA and NLFB32C only), see Installing Blower Accessory, page 8. 4. Route flexible gas line from manual shutoff valve into firebox through side. NOTICE: Most building codes do not permit concealed gas connections. A flexible gas line is recommended to allow accessibility from the firebox. The flexible gas supply line connection to the manual shutoff valve should be accessible. 5. Install and properly test gas log heater. Follow installation instructions included with the vent-free gas log heater that is being installed. 6. Replace firebox bottom and secure with screws. Continued 9 For more information, visit ® UNVENTED 32" LogMate® FIREBOX INSTALLATION Continued Figure 13 - Removing Firebox Bottom Screws Cut to7 1/4"Length Heater Base Mounting Bracket Firebox Bottom Figure 14 - Cutting Brackets INSTALLING FIREPLACE HOOD 1. Attach three zinc-colored shoulder screws to back of hood. 2. Insert hood into hood-mounting slots on firebox. 3. Hold hood in place. Insert two black Phillips screws through bottom of hood and tighten. Hood Hood Mounting Slot Screw Shoulder Screw Figure 15 - Installing Fireplace Hood INSTALLING FIREPLACE SCREEN 1. Insert each rod through nine rings located at top of screen. 2. Insert first rod into rear hole in left side of firebox. Fasten rod to rear hole near center of firebox using black shoulder screw. 3. Insert other rod into front hole on right side of firebox and fasten using remaining shoulder screw. Rear Hole Figure 16 - Installing Fireplace Screen (Shown Without Fireplace Hood for Clarity) .....................................................................................................................................................................................................................................................................................................................................................................................................

Herunterladen

Geben Sie zwei Ziffern: