NO. 1690990 Figure 1. A. Elbow B. Lockwasher, 1/4" C. Screw, 1/4-20 x 3 D. Hose, 6" ID E. Clamp F. Nut, 1/4" G. Clamp H. Clamp I. Capscrew, 3/8-16 x 2" J. Capscrew, 3/8-16 x 2-1/2" K. Hitch Extension L. Lockwasher, 3/8" M. Nut, 3/8" N. Housing O. Hose, 7" ID P. Nut, 1/4" Q. Lockwasher, 1 /4" R. Capscrew, 1/4-20 x 3/4 S. Tube Support T. Lockwasher, 1 /4" U. Nut, 1/4" V. Tube Support W. Capscrew, 1/4-20 x 3/4" X. Hitch A WARNING Do not operate the vacuum collector with any part

Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 & 3 of this manual and All SAFETY messages on the machine and its attachments before operating. 2.2.2 NOMENCLATURE The nomenclature picture above, Figure 1.1, shows the essential parts of the Yard Vacuum. It is recommended that all operators of this equipm

4.2 IMPELLER REPLACEMENT The impeller is a wear item. The actual wear rate is dependant on the types of debris the machine has been used to pickup. If the machine develops unusual noise and/or vibration STOP the engine immediately. After allowing the engine to cool, proceed with the following steps. 1. In an open area where fumes can safely dissipate, drain fuel into an approved container. 2. Drain engine oil. 3. Remove sparkplug wire from sparkplug and secure away from sparkplug. 4. With engine

10 Service – Every 25 Operating Hours.......................................................................... 10 Storage – Out of Season.............................................................................................10 SECTION 4- ADJUSTMENTS AND REPAIR .................................................................. 11 Engine Adjustments & Repair .................................................................................... 11 Impeller Replacement..........................

1. Adjust height of vacuum inlet. For maximum debris pickup, inlet should be as close to debris as possible without blocking airflow and engine speed set to “FAST”. 2. Inspect debris bag. It must be properly attached to machine, in good condition, clean and dry with the top zipper fully closed. Make sure that the accessory plug is installed into front hole in vacuum nozzle. 3. Start engine. Not all debris pickup will require that the engine speed be set to “FAST”. You can experiment with vacuum

No. SV25550HC SV25650B 7085638 7085687 Model Mfg. No. SV25500HV SV25550HV 7085644 7085642 COMMERCIAL MODELS Before operating your new machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! NOTE: Specifications are correct at time of printing and are

No. SV25550HC SV25650B SV25650B SV25650B 7085638 85633 7085634 1694489 COMMERCIAL MODELS Model Mfg. No. SV25500HV SV25550HV 7085644 7085642 Before operating your new machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! COPYRIGHT © 2003 SNAPPER PRO

6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle. 8. DO NOT start gas powered equipment in enclosed vehicles or trailers. 9. Keep the nozzle in contact with the rim o

Contents of Turbo Installation Kit 4 Initial Turbo Installation TURBO INSTALLATION Remove Mower Deck Remove the mower deck from the unit (see Operator’s Manual for instructions). Deflector Removal 1. Remove and retain the carriage bolts, washers, lock- washers, and nuts (A, Figure 3) holding the deflector rod to the deck. Remove and discard the deflector rod. Retain the deflector. Install Discharge Baffle 1. Attach the baffle bracket (A, Figure 4) under the mower housing as shown, and insert the