Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Snapper Dateigröße: 437.73 kb Dateiname: Unterrichtssprache:

10 Service – Every 25 Operating Hours.......................................................................... 10 Storage – Out of Season.............................................................................................10 SECTION 4- ADJUSTMENTS AND REPAIR .................................................................. 11 Engine Adjustments & Repair .................................................................................... 11 Impeller Replacement.................................................................................................. 11 Impeller Housing Liner Replacement ........................................................................ 11 TROUBLESHOOTING ..................................................................................................... 12 MAINTENANCE SCHEDULE........................................................................................... 13 PRODUCT REGISTRATION FORM ................................................................................ 14 IMPORTANT: The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your authorized dealer if you have questions. WARNING GAS ENGINES MAY REQUIRE A SPARK ARRESTER If the engine on this machine is not equipped with a spark arrester and is to be used on any forest, brush, or grass-covered unimproved land, a spark arrester must be added to the muffler before using the engine on such land. The spark arrester must be maintained in effective working order by the operator. In the state of California, the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See your authorized engine service center for muffler spark arrester options. 4 SETUP INSTRUCTIONS The majority of the assembly has been completed at the factory. After removing the machine from the shipping container you will be required to unfold the handles, attach the debris bag, and insert the accessory plug into the vacuum nozzle. Initial adjustments and operational tests were performed prior to shipping the machine. Due to the effects of shipping, handling and storage, the machine must be carefully inspected for loose, damaged parts and any necessary final adjustments completed at the time of setup. It is very important that you register your purchase to insure warranty coverage. Please fill out your product registration form and mail it to the address listed on the form. 1. Carefully remove the contents from the shipping container. You can avoid having to lift the machine by cutting the rear out of the box. The machine can then be rolled out. 2. Unfold the handles being careful not to kink the control cables and place in the operating position. Tighten the hardware securely. 3. Attach the bag adapter to the discharge opening. Open the discharge door and slide the adapter downover the two flanges at the opening. Make sure the adapter is secured in place on both sides. Close door. See Figures 1 and 2. 4. Attach two rear straps located near the top of the debris bag to the handles. See Figure 3. 5. Install accessory plug. Line up the two lugs on the plug with the two notches in the vacuum nozzle. Insert nozzle and rotate 90 degrees to lock in place. See Figure 4. 6. Fill engine crankcase with oil to proper level. Referto engine owner’s manual for specifications. 7. Move machine to open area where fumes can safely dissipate and away from all sources of ignition. Fill fuel tank. Refer to engine owner’s manual forspecifications. Do not over fill. 8. Setup is complete. Please proceed to the Pre-Start Check List. Follow and complete each step carefully. FIGURE 2 ATTACH STRAPS TO HANDLES FIGURE 3 DISCHARGE DOOR BAG ADAPTER MOUNTING FLANGE FIGURE 1 INSERT ACCESSORY PLUG INTO NOZZLE FIGURE 4 5 Section 1 – FAMILIARIZATION ENGINE SPEED CONTROL FIGURE 1.1 ENGINE SPEED CONTROL DEBRIS BAG HEIGHT CONTROL ENGINE PRIMER DISCHARGE DOOR VENT, WITH ZIPPERS ACCESSORY PLUG VACUUM NOZZLE BRIGGS (PRIMER) HONDA (CHOKE) STOP SLOW FAST CHOKE 1.1 INTRODUCTION This manual has been prepared for the operator’s of the Yard Vacuum. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 & 3 of this manual and All SAFETY messages on the machine and its attachments before operating. 2.2.2 NOMENCLATURE The nomenclature picture above, Figure 1.1, shows the essential parts of the Yard Vacuum. It is recommended that all operators of this equipment become thoroughly familiar with the controls, components, and operation of this machine before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference. 6 Section 1 – FA...

Herunterladen

Geben Sie zwei Ziffern: