Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
* 7 305-8792 Grip-Height Adjustment § 39 712-183 Angle Bracket Special 8 310-8749 Height Adj. Grip Ass’y-icomplete) 40 736-155 Rubber Washer 9 310-8730 Height Adj. Grip Bracket Ass’y § 41 394-9966 Hand Knob 10 711-223 Spacer Bushing 42 395-9998 Handle Knob 11 736-159 Flat Washer * 43 310-8795 Handle Extension Assembly 12 714-507 Cotter Pin 3/32 x 3/4 lg. * 44 312-8895 Adapter-Grass CatcherDbl.Deck 13 732-153 Spring 45 712-287 Hex Nut 1/4-20 thd. * 14 .395-8735 Height Adjustment Bracket 46 736-329 Spring Lockwasher for 1/4 Screw* 15 736-119 Spring Lockwasher for 5/16 sew. 47 714-104 Int. Hair Pin Cotter* 16 712-267 Hex Nut 5/16-18 thd. 48 710-286 Truss Head Mach. Screw 17 310-8743 Rod Height Adjustment 1/4-20x1/2 lg. * 18 711-225 Clevis Pin 49 394-9962 Engine Shroud 19 395-8956 Height Adj. Ass’y-Front&Rear 50 310-10008 Handle-Lower 20 714-115 Cotter Pin * 51 746-145 Cable Clip 21 312-8125 Blade - 21” 52 710-405 Curved Hd. Scr.5'/16-18 x 1-3/4 lg. 22 712-372 Hex Centerlock Nut 5/16-18 thd. 53 712-107 Centerlock Nut 1/4-20 23 501-9383 Wheel Assembly 54 310-10011 Handle — Upper 24 736-105 Belleville 55 718-138 Handle Grip 25 741-114 Ball Bearing 56 710-606 Hex Hd. Cap Sew. 1/4-20 x 1/2 lg.* 26 738-213 Axle Bolt 58 310-10033 Control Throttle (complete) 28 305-9871 Hub Cap 59 732-139 Conduit and Wire f 29 710-113 Hex Head Cap Screw 60 901-7627 Ferrule Assembly t 3/8-24 x 1-5/8 lg.(Heat Treated) 61 310-9848 Control Bracket Ass’y — Throttlet 30 736-169 Spring Lockwasher for 3$5 screw * 62 305-7470 Knob t 31 714-365 Key - Hi-Pro No. 505* 68 312-7919 Anti Scalp Plate 32 748-100 Blade Adapter 69 312-7299 Oil Fill Trough 33 712-123 Hex Nut 5/16-24 thd. 70 710-259 Hex Hd Cap Sew 5/16-18 x 5/8 lg. * * For faster service, obtain standard nuts, bolts, and washers locallyl If these items cannot be obtained locally, order by part number and size as shown on the parts list. . t Part of Throttle Control (complete) 310-10033 § Part of Height Adjustment Grip Ass’y - (complete) 310-8749. NOTE: A brief break in period is essential to insure maximum engine life. This consists of running the engine at half speed for a period of time required to use one tank of gasoline. This is necessary on the initial run only. It is also recommended that the oil be changed after five (5) hours of operation. This allows for the removal of impurities which may have accumulated duringthe break in period. Subsequent oil changes should be made as stated in the engine manual. Always check oil before using your mower. Be sure crankcase is full. CUTTING HEIGHT ADJUSTMENT This mower can be adjusted for seven cutting heights from 1%” to 3”. To change height depress the push cap on the height adjustment lever and move it forward to lower the cutting height and move to the rear to raise the cutting height. The one lever adjusts all four wheels at the same time. \ \ I a I J / LOW 1 * 3 HIGH CUTTING HEIGHTS NOTE: This instruction manual covers various models and all accessories shown do not necessarily apply to your model mower. MTD PRODUCTS INC extends its warranty only on the mower. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines — Gasoline”. Find It Fast In The 'Yellow Pages' FORM NO. 770-239 1 C ASSEMBLY INSTRUCTIONS NOTE: Before operating your mower, check all nuts and bolts for proper tightness. Be sure to check the Blade Bolt! STARTING ENGINE With the throttle control lever conveniently mounted on the handle, starting, fast, slow and stopping of engine is conveniently controlled with one lever,, After the engine has been properly fueled and oiled (Refer to engine operating and maintenance instructions..) start engine in the following manner: 1. Move throttle control lever to “start” position. 2. Operate a new engine at intermediate speeds and light load for the first few hours as you would a new automotive engine. 3. To stop engine, move speed control lever to stop position. 4. If carburetor needs adjustment to start or for operation, see “Carburetor Readjustment” section in engine manual CUTTING For best lawn results in most areas, grass should not be cut below two inches (medium wheel position), as cutting the grass blades short tends to retard its growth. It is important that when sharpening the cutting edges of the blade you grind equal amounts from each cutting surface to preserve the blade balance. An unbalanced tlade will vibrate. Never operate the mower with a bent or unbalanced blade, as it will cause damage to the mower and engine. A sharp blade insures best cutting results and minimum engine wear. Never install or remove blade with engine spark plug wire attached. MAINTENANCE CUTTING BLADE — The blade may easily be removed for grinding or replacement as follows: 1. Remove bolt and lock washer holding blade and hub assembly to engine crankshaft. 2. Remove blade an...