Login:
Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Anleitung DeWalt, modell 4262-1

Hersteller: DeWalt
Dateigröße: 1.31 mb
Dateiname:
Unterrichtssprache:
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


E - Drill and Magnet Interlock The drill will not operate unless the button is pushed and the red indicator is on. If the operator attempts before turning on the magnet, will not function. 9 To start the drill: 1. Push the magnet button to activate the magnet. 2. Make sure the red indicator light is on. If the light is flashing, check for the following: • Low voltage at plug • Loose motor connection • Mag panel buttons are jammed or stuck If flashing light still occurs, take entire unit to an authorized service center. 3. Push a drill button for forward or reverse. If a loss of line voltage occurs while the drill is running, the drill will stop. Gear Shift Lever Fig. 7 Cat. Nos. 4292-1 and 4297-1 operate in either high or low speed. Use low speed for large diameter bits and high speed for small diameter bits (see “Specifi cations” chart). To change speeds, turn the drill off and rotate the lever up or down while the drill is coasting to a stop. NOTE: To avoid damage to the gearbox, do not shift at full speed, when the tool is under load, or when the tool has stopped. The gear shift on the motor is labeled: L - for low speed H - for high speed Typical Operation 1. Insert the bit into the chuck or (see “Keyed Chuck" or "Morse Taper Socket” and “Using Twist Drills" and "Using MILWAUKEE STEEL HAWG™ Cutters”). 2. Place the magnetic prepared surface. 3. Position the unit so that the tip of the drill bit is directly over the center of the hole to be drilled. 4. Push the magnet button. The red indicator light will turn on. 5. Attach the safety chain if drilling overhead or on a vertical surface. 6. Check the gear speed setting and change if required. 7. Push the forward or reverse button as required. 8. Drill hole (see “Using Twist Drills" and "Using MILWAUKEE STEEL HAWG™ Cutters”). 9. Push the “Drill Off” button. 10. Remove the chain (if drilling overhead or on a vertical surface). 11. Push the magnet button. The red indicator light will turn off. Using the Adjustable Base (4203 only) Fig. 8 1. Turn the drill motor off. 2. Position the magnetic base so that the drill bit is near the desired hole location and push the magnet button. The red indicator light will turn on. 3. Loosen the adjusting handle located at the back of the housing base. Move the housing to position the drill bit over the center of the hole. Tighten the adjusting handle securely. Keyed Chuck (Select Models) Fig. 9 1. Open the chuck jaws wide insert the bit. Be sure chuck jaws are clean. prevent the bit from 2. When using drill bits, insert the bit into the chuck. Center the bit in the chuck jaws and lift it about 1/32" off of the bottom. Tighten the chuck jaws by hand to align the bit. 3. Place the chuck key in each of the three holes in the chuck, turning it clockwise as shown below. Tighten securely. 4. To remove the bit, insert the chuck key into one of the three holes in the chuck and turn it counterclockwise. - Clockwise (Tighten) - Counterclockwise (Loosen) Morse Taper Socket ...

Dieses Handbuch ist für folgende Modelle:
Bohrmaschinen und Schrauber - 4202 (1.31 mb)
Bohrmaschinen und Schrauber - 4202 (1.31 mb)
Bohrmaschinen und Schrauber - 4206-1 (1.31 mb)
Bohrmaschinen und Schrauber - 4204-1 (1.31 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien