Login:
heruntergeladen wurde: 7   Dateigröße: 737 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment. LIMITED WARRANTY STATEMENT LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS MFG. CO. is warranted against defects in materials and workmanship for a period of one year fr

heruntergeladen wurde: 7   Dateigröße: 737 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION CAUTION: Equipment REFER TO EXPLODED VIEWS PAGE 9 FOR COMPONENT Electrical Damage NAMES/NUMBERS DO NOT plug in or energize this appliance until all Installation Instructions are read and followed. Damage to the Brewer will occur if these instructions are not followed. CAUTION: Unstable Equipment Hazard It is very important for safety and for proper operation that the warmer is level and stable when standing in its final operating

heruntergeladen wurde: 0   Dateigröße: 2 mb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

CAUTION: BURN HAZARD Exposed surfaces of dispenser and any container may be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD DO NOT fill water bottle with hot water. Splashing hot water can cause burns. OPERATION (continued) 9 INITIAL SET-UP: PORTABLE DISPENSERS 1. Turn POWER switch OFF. Turn WATERLINE / PORTABLE switch to PORTABLE Turn HEATER switch OFF. Turn COLD/HOT / HOT/HOT switch to HOT/HOT Turn DISPENSE / FLUSH switch to flush 2. Add water to tank. NOTE: To avoid an ove

heruntergeladen wurde: 1   Dateigröße: 2 mb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

Disconnect dispenser from electric power and allow to cool. Open front door. FOR EACH DISPENSING STATION: 2. Remove the blender housing assembly: a. Remove funnel cap: Lift cap straight up. Some twisting may be necessary. b. Turn blender housing 1/4 turn clockwise while pulling away from blender base. c. Disassemble funnel, diverter and cap from blender housing. 3. Remove whipper blade: Pull whipper blade straight off of the motor shaft. Note the flat portion of the motor shaft, and how it relat

heruntergeladen wurde: 1   Dateigröße: 806 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

This manual should be considered a permanent part of this appliance. The manual must remain with the appliance if it is sold or moved to another location. This dispenser is and listed under file E9253. This dispenser meets Standard 4 only when installed, operated and maintained in accordance with the enclosed instructions. CAUTION: Equipment Electrical Damage DO NOT plug in or energize this appliance until all Installation Instructions are read and followed. Damage to the dispenser will occur if

heruntergeladen wurde: 6   Dateigröße: 806 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

WARNING ELECTRIC SHOCK HAZARD: Dispenser must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the appliance or result in decreased performance. Such damage is not covered by warranty. IMPORTANT: Do not connect dispenser to electrical power until you are ready to fill th

heruntergeladen wurde: 0   Dateigröße: 806 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

This will prevent boiling water in the dispenser, NOTE: Thermostat is adjustable to a maximum of 199.F. IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line. IMPORTANT: Before setting lid assembly into tank, make sure tank lid gasket is properly seated on flange of lid. 10 SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT

heruntergeladen wurde: 0   Dateigröße: 806 kb   Hersteller: Bloomfield  
Kategorie: Dispenser
@name

Install a new seat cup, making sure the knob on the stem is fully inserted into the pocket of the seat cup, and the skirt of the seat cup is fully inserted into the bonnet Reassemble in reverse order. IMPORTANT: When replacing heating element, also replace seal gaskets. NOTE: Any abrasion or roughness on the flat end of the seat cup will require replacing the seat cup: 11 SERVICING INSTRUCTIONS (continued) SERVICING INSTRUCTIONS (continued) CAUTION CHEMICAL BURN HAZARD Deliming chemicals are cau





Kategorien