Stimmen - 4, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Cuisinart Dateigröße: 373.37 kb Dateiname: wch-1500.pdf Unterrichtssprache:

1. Make sure unit is plugged into outlet. 2. Make sure air has been purged from internal tanks, as stated on page 5. 3. If there is water in the tanks, it will take about 80 minutes for the water to chill the first time. It takes only about 30 minutes for subsequent fi ll-ups. COLD water LED light turns off even though cold water is not dispensed. Large amount of room temperature water was dispensed. Allow up to 30 minutes for water to chill and LED light will turn on. Energy Saver mode LED does not light up. 1. Power is not on. 2. Energy Saver is in Off position 1. Make sure unit is plugged into outlet. 2. Make sure Energy Saver switch is in its On position. Heater is still working and hot water is still available in Energy Saver mode. Contact Customer Service. Filter timer does not show “Filtering” or “Replace.” Battery is dead. Contact Customer Service for replacement fi lter timer. Leakage on the countertop. 1. Water tanks are not properly seated on base. 2. Drainage plugs are not fully engaged. 1. Make sure water tanks are seated properly on the base. 2. Ensure that drainage plugs are correctly installed on the bottom of the base. Water leaks from the top cover. Water tanks are overfilled. Drain excess water from tanks by pressing push buttons. ROOM temperature water is warm. Allow up to 30 minutes for cold water to chill and blue LED light to turn on. HOT temperature water is not hot. Energy Saver is in On position. Make sure Energy Saver is in its Off position. Bottom of unit STORING THE UNIT 1. Turn the unit off and unplug it from outlet. 2. Remove empty water tanks, filter and cover. 3. Allow hot water to cool, then bring base to sink. 4. Drain internal reservoir by tilting unit slightly and removing the 2 plastic drainage plugs from bottom of unit. Plugs are tightly inserted and must be gently, but firmly, worked to remove. 5. When water has completely drained, replace plugs, tanks, filter and cover. DrainagePlugs 6. Your Cuisinart® ® Countertop Filtration System is ready to store. TECHNICAL SPECIFICATIONS Unit: WCH-1500 1 Cuisinart® ® Countertop Filtration System 1 Cuisinart® Water Filter System Capacity up to 3 months/ 48 gallons/ 181 liters Maximum Input Temperature 104°F (40°C) Minimum Input Temperature 34°F (1°C) Maximum Output Temperature 194°F (90°C) Minimum Output Temperature 44°F (7°C) Rated Service Flow 6 gallons / 22.7 liters per day (may vary according to water conditions) Electrical Requirements AC~120V 60Hz 3.7A 450W System Tested and Certified by WQA against NSF/ANSI Standard 53 for the reduction of Lead, Benzene, Cadmium, Copper, Mercury, Tetrachloroethylene, Toluene, and Standard 42 for the reduction of Chlorine Taste and Odor. See Performance Data Sheet for specific test conditions and results. Claims are calculated based on WQA accepted practice of average percent reduction. The contaminants or other substances removed or reduced by this water treatment device are not necessarily in all users’ water. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Individuals requiring water of specific microbiological purity should consult their physician. The Cuisinart® ® Countertop Filtration System processes approximately 48 gallons/ 181 liters. When the Cuisinart® Water Filter (GF-80) exceeds filtering capacity, replacement is essential for the product to perform as represented. In the United States, replacement filters cost generally $19.99 per filter. Replacement filters may be purchased at most retail outlets. The performance of the filter may vary based on local water conditions. Hot water should not be used with the Cuisinart® Water Filter (GF-80) as it will affect the filter’s performance. Refer to the Operating Instructions and Cleaning and Care for general unit operation and maintenance requirements. Testing was performed under standard laboratory conditions; actual performance may vary. PERFORMANCE DATA SHEET PERFORMANCE DATA SHEET FOR MODELS WCH-1000 AND WCH-1500 CONTAMINANT REMOVAL DATA IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs. It is recommended that, before purchasing a water treatment unit, you have your water supply tested to determine your actual water treatment needs. Performance testing conducted by WQA. These systems have been tested according to NSF/ ANSI Standard 53 and 42 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for the water leaving the system, as specified in NSF/ANSI Standard 53 and Standard 42. Testing was performed under standard laboratory conditions; actual performance may vary. Removal Removal Action Level Hardness Temp Inlet Substance Influent Water Avg. (mg/L) Influent Challenge Concentration (mg/L) Filter Effluent Max. (mg/L) Percen...

Herunterladen

Geben Sie zwei Ziffern: