Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Sony Dateigröße: 567.84 kb Dateiname: Unterrichtssprache:

Follow Steps 1 to 4 in “Creating Your Own Program” on page 11. The A indication appears in the display. 2EWhen you record on both sides of the tape, press P to insert a pause. The “P” and AB indications appear in the display and the playing time is reset to “0.00.” When you record on one side of the tape, skip this step and go to Step 4. A pause is counted as one track You can program up to 31 tracks when you insert a pause. 3ERepeat Steps 2 to 4 in “Creating Your Own Program” on page 11 to create the program for side B. 4EStart recording on the deck and then press a on the player. When you record on both sides of the tape, the player pauses at the end of the program for side A. 5EWhen you record on side B, reverse the tape and press aor Pon the player to resume playing. You can check the total playing time while programming (Program Edit) To select a track, press ­or ±and check the total playing time. Then press PROGRAM to confirm your selection. To check and change your program See page 12. The A indication appears while checking the program for side A and B while checking the program for side B. Recording a CD by Specifying Tape Length (Time Edit) (except for CDP-C450Z, CDP-C350Z and CDP-C250Z) You can have the player create a program that will fit the length of the tape. The player automatically creates a program, keeping the original order of the disc. The program can contain up to 32 tracks (a pause inserted between tracks is counted as one track). Note that tracks numbered over 20 cannot be programmed automatically. EDIT/TIME FADE ­/±· DISC SKIP 1EPress DISC SKIP to select the disc. 2EPress EDIT/TIME FADE repeatedly before you start playing until “EDIT” appears and “A” in the A indication flashes in the display. 3EPress ­or ±to specify the tape length. Each time you press these buttons, the display changes as shown below, with the tape length of one side following each indication. nC-46 .C-54 .C-60 .C-74 .C-90 .- -. - -N (23.00) (27.00) (30.00) (37.00) (45.00) 4EPress EDIT/TIME FADE to have the player create the program. The display shows the tracks to be recorded. “B” in the B indication flashes in the display. 5EWhen you record on both sides of the tape, press EDIT/TIME FADE again. The player inserts a pause, then creates the program for side B. The display shows the programmed tracks. When you record on one side of the tape, skip this step. 6EStart recording on the deck and then press aon the player. When you record on both sides of the tape, the player pauses at the end of the program for side A. (Continued) Recording From CDs Recording From CDs 7EWhen you record on side B, reverse the tape and press aor Pon the player to resume playing. To cancel Time Edit Press CONTINUE. You can program the tracks you want in advance Select the tracks before doing the above procedure. The player creates a program from the remaining tracks. You can freely specify the tape length Set the tape length using number buttons. To enter “0,” use button 10. Example: When the tape length of one side is 30 minutes and 15 seconds Press 3, 10, 1 and 5. You can check and change the program See page 12. When track numbers flash in Step 3 or 4 (CDP-CE505 only) This means that there is a portion remaining on the tape after the player has programmed all the tracks so that you can add more tracks to the portion (Link Edit). You can also select another disc and add the tracks on the disc you select if the tracks on the current disc are shorter than the remaining time. Press EDIT/TIME FADE to have the player add the tracks, or press number buttons of the tracks flashing in the display. When you want to add tracks on another disc, press DISC SKIP to select the disc, and then press number buttons of the track. After adding the tracks, press ato start playing. If you don’t need to add tracks, just press ato start playing. When “B” in the AB indication flashes This means that more than 1 minute remains on the tape but no track on the current disc fits the remaining portion. If you add tracks on other discs, select the disc you want and follow the procedure above. Fading In or Out You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector. ­/±· EDIT/TIME FADE*FADER** Number buttons *except for CDP-C450Z, CDP-C350Z and CDP-C250Z **except for CDP-CE505 and CDP-C450Z (CDP-CE505 and CDP-C450Z only) Number buttons FADER ( =/+ To Press FADER Start play fading in During pause. FADE lights up in the display and the Q indication flashes. The play fades in. End play fading out When you want to start fading out. FADE lights up in the display and the q indication flashes. The play fades out and the player pauses. Note Fading lasts for about 5 seconds. However, when you press FADER during Music Scan (see page 10), the play fades out for about 2 seconds. Changing the fading time (CDP-CE505 and CDP-C450Z only) You can change the fading time fr...

Herunterladen

Geben Sie zwei Ziffern: