Maintenance Procedures Most guide bar problems can be prevented merely by keeping the chain saw well maintained. Incorrect filing and non-uniform cutter and depth gauge settings cause most guide bar problems, primarily resulting in uneven bar wear. As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in making straight cuts. Insufficient guide bar lubrication and operating the saw with chain that is too tight will contribute to rapid bar wear. To help minimize

If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020").The spark plug should be replaced after about a month in operation or earlier if necessary. Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor. Lubricating the bar tip sprocket Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease. Needle

32 Checking, maintaining and servicing chain saw safety equipment .................................................. 33 Muffler ................................................................... 35 Starter ................................................................... 36 Air filter .................................................................. 37 Spark plug ............................................................. 37 Lubricating the bar tip sprocket ............................. 37

Never starve the bar and chain of oil. Running the saw with too little oil will decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and cause excessive wear of bar from overheating. Too little oil is evidenced by smoke, bar discoloration or pitch build-up. A B Fig. 10 Automatic Oiler Your chain saw is equipped with an automatic gear driven D oiler system. The oiler automatically delivers the proper amount of oil to the bar and chain. As the engine speed increases,

power 8000 rpm Motorwelle 6,2 hp Fuel tank capacity 0.85 I Drehzahl bei max Oil tank capacity 0.55 I Leistung 8000 rpm Ignition system Femsa electronic GEF Kraftstofftank 0,85 I Ignition advance CD type243 Ultank Zundung 0,55 I Elektronisch, Sparking plug Champion CJ 7 Y Bosch WKA 225 T 36 Vorzundung Femsa GEF CD-Typ~4. Carburetter Tillotson HS Venturi 1 Zundkerze Champion CJ 7 Y Chain lubrication Automatic. Amount of oil Bosch WKA 225 T 36 adjustable in four positions. Stationary when Vergaser

Your saw is equipped with an automatic oiler system. CHAIN MAINTENANCE Chain Tension Check the chain tension frequently and adjust as often as necessary to keep the chain snug on the bar, but loose enough to be pulled around by hand. Breaking in a New Saw Chain A new chain and bar will need chain readjustment after as few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will begin to lengthen quickly. Never have more WARNING: than 3 links removed

Asegurese de aflojar el tornillo de la barra guia lo suficiente para dejarlo apretado con la mano; gire hacia la derecha el tensador de la cadena para tensar esta. Consulte el apartado Reemplazo de la barra y de la cadena mas arriba en este manual, donde encontrara informacion adicional. . La cadena, estando fria, esta bien tensada cuando no hay holgura de la misma en la parte inferior de la barra guia, la cadena se siente bien ajustada en la barra, y puede avanzarse con la mano sin ningun atora

out of the bar groove. NOTE: New chain tends to stretch, check chain tension frequently and tension as required. caution: Chain tensioned while warm, may be too tight upon cooling. Check the “cold tension” before next use. Chain Maintenance See Figures 31 - 32. WARNING: Remove the battery pack and make sure the chain has stopped before you do any work or making any adjustments on the saw. Failure to do so may result in accidental starting and possible serious injury. Use only low-kickback chain

E EEEEn nnnng ggggl lllli iiiis ssssh hhhh ( ((((2 2222- ----4 44442 2222) )))) Lea detenidamente el manual de instrucciones y asegurese de entender su contenido antes de utilizar la maquina. S SSSSp ppppa aaaan nnnni iiiis ssssh hhhh ( ((((4 44443 3333- ----8 88884 4444) )))) 115 13 81-96 Rev.3 2008-12-16 KEY T O SYMBOLS 2 – English 115 13 81-96 Re v .3 2008-12-16 Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to th

Remove the cut pieces from the cutting area. By leaving them in the cutting area, you increase the risk for inadvertently getting a kickback, as well as increasing the risk of losing your balance while working. The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you finish the cut. Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the c