Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: AquaPRO Dateigröße: 2.12 mb Dateiname: Unterrichtssprache:

Controls Toggling Between Heating and Cooling Mode The unit will default to the heating mode. If the cooling mode is desired, press the SET button until the H-C screen is displayed. Then press the arrow buttons until “COL” is displayed on the screen. This puts the unit into cooling mode. The water temperature set point will now be the water temperature that the unit is cooling the water to. When the unit is in cooling mode, the screen will flash between the current water temperature and “COL” to remind the user that cooling mode is activated. Defrost Cycle Your AquaPRO® h/c unit is capable of keeping your pool warm in very cool temperatures. Most pool heaters will not operate below 50°F. Your h/c unit will work down to 38°F by utilizing a “defrost cycle”. It does this automatically by sensing the coolant temperature and reversing operation for 2 minutes to defrost the evaporator coil and will resume heating function after defrosting the evaporator coil. PRO1100e TCE and PRO1300 TCE Selecting Functionality of Unit This unit is capable of operating as a Time Clock Override (TCO) or as the Time Clock Eliminator (TCE). If you already have a time clock on your swimming pool and would like to maintain its normal operation with the added benefit of a heat pump time clock override – please review the section for the Time Clock Override. If you do not own a time clock for your pool system - please review the section for the Time Clock Eliminator. Time Clock Eliminator (TCE) Operation Please read the functions of this feature carefully. All wiring and electrical connections must be performed by a qualified electrician. Installation must be in accordance with local and national codes. This section allows you to run the heat pump at set intervals during the day. If you have a time clock, and would like to use it please refer to the Time Clock Override section. For the TCE feature to work, your pool pump must be wired to the heat pump See figure 7 for wiring the TCE feature • This unit is prepared at the factory with the TCE feature installed, but set to the “off” position in the “FIL” mode. You will need to set the hours of run time for the pump and filter system. See “activating and setting system run time” below. • The function of the TCE is done through a timing sequence of 6 periods per 24 hours. You select the hours for your required filter pump run time, and the heater takes care of the rest. It does this by dividing the system run time equally over the 6 periods, turning the pump on for 1/6th of the specified run time and off the remainder of the period unless additional heating is required. The heater will always operate the system on a daily basis for the amount of run time you have selected. The timing sequence begins at the initial start up. • If your pool is at or above the desired operating temperature, the heater will run the system the desired hours each day and spread the time out evenly between the 6 periods. This makes for better filter operation and allows the heater to update the water temperature 6 times per day. • If your pool needs heat, the heater will continue to run the system until the desired temperature is met. If the amount of run time exceeds a period’s run time, the excess time will be subtracted from the next run period(s). Please note that on cold and / or windy days, the unit could run for long times to generate and maintain the desired pool temperature. Please see the “application” section about “pool blankets” to help maintain your pool’s temperature. • The timing function built into the TCE will always run the heat pump for 15 minutes every 4 hours to determine if more heat is needed to maintain the pool’s desired temperature - even if all of the available run time was used in previous cycles. This provides a couple of added benefits. Pools will lose most of their heat at night if left uncovered, however, since the unit is checking for and adding heat when needed, it prevents long recovery times when compared to non-TCE units. The other benefit is that some states and electric utility companies offer a discount for off-peak usage of electricity. Please contact your electricity provider if you have questions. • Example of TCE operation – you require the system to run for 12 hours to meet your pool filtering needs. This means for each of the 6 periods, the heater will run the system for 2 hours and then turn off for 2 hours. If the system needed to run for 3 hours in one of the periods to reach the desired pool temperature, the next period would be 1 hour on and 3 hours off unless additional heating is needed. The cycle continues for 6 periods and renews at the end of each 24 hours. Please call AquaPRO® Systems at 1-877-AQUA-SYS (1-877-278-2797) if you need further clarification of this feature’s operation. Activating and Setting System Run Time - TCE Operation • To set the run time of the system, push the “SET” button repeatedly until “FIL” displays. Then using the “up” and “down” a...

Herunterladen

Geben Sie zwei Ziffern: