Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Directed Electronics Dateigröße: 187.48 kb Dateiname: Unterrichtssprache:

W WWa aar rrn nni iin nng gg: ::DO NOT connect a level control knob from other manufacturers to the Remote Sub Level Control of any Directed amplifier. Even though the connectors fit properly, the control knob and connector pin positions may be different and the amplifier will be damaged. FIGURE 1—AMPLIFIER CONNECTIONS 700/6 FRONT 12 34 © 2003 Directed Electronics, Inc REAR PANEL CONNECTIONS 1. S SSp ppe eea aak kke eer rr O OOu uut tt T TTe eer rrm mmi iin nna aal lls ss - Connect the remote turn on lead of the head the speakers to these terminals. unit or signal source. If a (+) 12 (Refer to the Speaker Wiring volt remote turn on lead is not Diagramssection of this guide.) available, the Remote Power Adapter (P/N #55000) can be 2. P PPo oow wwe eer rr F FFu uus sse ees ss - --These fuses protect used to supply a remote turn on the amplifier against internal elec signal. DO NOT connect this trical damage and are meant to terminal to constant (+) 12 volt. protect the amplifier only. All other power connections should be fused 5. G GGr rro oou uun nnd dd - --Connect this terminal at the source. directly to the sheet metal chassis of the vehicle, using the shortest 3. ( ((+ ++) )) 1 112 22 V VVo ool llt tt P PPo oow wwe eer rr - Connect this wire necessary to make this terminal through a FUSE or CIRCUIT connection. Always use wire of the BREAKER to the positive terminal of same gauge or larger than the (+) the vehicle battery or the positive 12 volt power wire. The chassis terminal of an isolated audio connection point should be scraped system battery. free of paint and dirt. Use only quality crimped and/or soldered W WWA AAR RRN NNI IIN NNG GG: ::Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within connectors at both ends of this 12 inches of the battery terminal connection. wire. DO NOT connect this terminal 4. R RRe eem mmo oot tte ee T TTu uur rrn nn O OOn nn - This terminal directly to the vehicle battery turns on the amplifier when (+) 12 ground terminal or any other volt is applied to it. Connect it to factory ground points. FIGURE 2—AMPLIFIER CONNECTIONS 700/6 REAR 1 2 345 © 2003 Directed Electronics, Inc TOP PANEL CONTROLS 1. I IIn nnp ppu uut tt G GGa aai iin nn A AAd ddj jju uus sst ttm mme een nnt tt - Controls amplifier sensitivity and is used to match the input level of the amplifier to the output level of the signal source. 2. C CCr rro oos sss sso oov vve eer rr S SSe eel lle eec cct tti iio oon nn S SSw wwi iit ttc cch hh Controls the type of filter for the onboard active crossovers. FLAT does not attenuate any frequencies and is for full-range speaker systems. HPF attenuates low frequencies and is used for mid-range speakers and tweeters. LPF attenuates high frequencies and is typically used for subwoofers. 3. C CCr rro oos sss sso oov vve eer rr F FFr rre eeq qqu uue een nnc ccy yy A AAd ddj jju uus sst ttm mme een nnt tt Adjusts the crossover point for the on-board active crossovers. FIGURE 3—AMPLIFIER CONTROLS 700/6 TOP 4. B BBa aas sss ss E EEQ QQ S SSw wwi iit ttc cch hh - --Adds 8 db of additional boost to channels five and six output when active. 5. I IIn nnp ppu uut tt P PPa aar rra aal lll lle eel ll S SSw wwi iit ttc cch hh - Controls the input signal to the indicated channels. If the 3+4 switch is ON, channels three and four will derive their signal from channels one and two RCA jacks and no input is needed. If the 3+4 switch is OFF, channels three and four RCA jacks must have input. If the 5+6 switch is ON, channels five and six will derive their signals from channels one through four RCA jacks and no input is needed. If the 5+6 switch is OFF, channels five and six RCA jacks must have input. . . . 4 . . . . 3 2 . . . . 1 . . . . . . . . . . . . . . 5 © 2003 Directed Electronics, Inc TOP PANEL FEATURES Control Panel Cover The gain and filter controls are located under a control panel cover on top of the amplifier. The control panel cover must be removed to gain access to the gain and filter controls. Remove/Install Four Allen-head screws hold the control panel cover to the amplifier top panel, one at each corner. They can be removed with the wrench supplied in the hardware pack. SPEAKER WIRING DIAGRAMS Stereo operation (top view) Four Channel Stereo with Mono Sub Six Channel Stereo © 2003 Directed Electronics, Inc Tri amp operation (top view) Bridged operation (top view) Three Channel N NNO OOT TTE EE: :: When wiring the 700/6 for three channel operation, connect the left audio signal to both channels one and two RCA jacks and the right audio signal to both channels three and four RCA jacks using RCA Y adapters. © 2003 Directed Electronics, Inc CROSSOVER SETTINGS AND GAIN ADJUSTMENT Your Directed Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier. • For full-range and simultaneous stereo/mono bass app...

Herunterladen

Geben Sie zwei Ziffern: