For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2). 1. Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door control by color: white to 2 and white/red to 1. 2. Door Control Button: Fasten securely with 6ABx1-l/2" screws. Console Model: Pry off cover along one side witha screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4" self-tapping screws (standard installation) or 6-32x1" machin

Fasten the manual near the garage door after installation, Complies with UL 325 _11 "_ regulations effective January I, I993 I:RRFTSMRNo 1/2 P GARAGE DOO OPENE [] Safety Precautions [] Assembly [] installation [] Adjustment [] Care and Maintenance [] Operation [] Troubleshooting [] Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Contents Page A review of safety alert symbols ................................. 2 You'll need tools ................................................

Fasten the manual near the garage door after installation. Complies with UL 325 /11 ii "N_ regulations effective January !, 1993 I:RRFTSMRNo 1/2 HP GARAGE DOOR OPENER • Safety Precautions • Assembly • Installation • Adjustment • Care and Maintenance • Operation • Troubleshooting • Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Contents Page Contents Page A review of safety alert symbols ................................. 2 Install the light and lens ..........................

ANY number is pressed in darkness this feature allows user to press ANY number before entering the 4-digit code Power Supply: Operates from the garage door opener power with a battery b&ck-up for code memory and light-IMPORTANT NOTE: When illumination is needed, ed keyboard Unit wiU not operate without battery avoid pressing keyboard area which contains the first code number. DISCONNECT THE POWER TO THE GARAGE DOOR OPENER BEFORE BEGINNING INSTALLATION. STEP 1--SECTIONAL DOORS: Draw two intersect

• If using extension brackets or wood blocks, adjust right and left assemblies to the same distance out from the mounting surface. Make sure all door hardware Figure 3 WALL MOUNT (RIGHT SIDE) obstructions are cleared. <_r Extension Floor installation (Figure 4): d;ll Bracket (See Accessories) • Use wood blocks or extension brackets (See (Provided with Accessories) to elevate sensor brackets so the lenses Extension Brackel will be no higher than 6" (15 cm) above the floor. • Carefully measure and

If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install. . Be sure that all remote control push buttons and battery indicator lights are off. 2. Remove the bell wire from the Wall Control terminals and operate from the remote control only. If this solves the problem, the Wall Control is faulty (replace), or there is an intermitt

Attach sprocket cover securely. Never operate opener Dispensing Carton while your hand is near the opener sprocket. Opener Sprocket Figure 2 Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Keep Chain and CabIe Taut When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag. See master link procedure, Figure 1. • With the trolley against the screwdriver, dispense the cable around the pulley. • Proceed back aroun

28 Adjustment Step 2 Adjust the Force Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door. The door will stop in the up direction if anything interferes with its travel. The door will reverse in the down direction if anything interferes with its travel (including binding or unbalanced doors). If the forces are set too light, door travel may be interrupted by nuisance reversals in t

• Any repair to or adjustment of the garage door (including springs and hardware). • Any repair to or buckling of the garage floor. • Any repair to or adjustment of the opener. Without a properly installedsafetyreversalsystem, persons(particularlysmall children)couldbe SERIOUSLYINJUREDor KILLEDby a closing garage door. • Safetyreversalsystem MUSTbetested everymonth. • Ifonecontrol(forceortravellimits) isadjusted,the othercontrol mayalsoneedadjustment. • Nter ANYadjustmentsare made,the safetyreve

If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. To avoid installation difficulties, do not run the opener at this time. To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. Do NOT use an extension cord, 2-wire adapter, or change the plug in any way to make it fit your outlet. Right Wrong If permanent wiring is required by your local code, refer to the following pro