If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install. . Be sure that all remote control push buttons and battery indicator lights are off. 2. Remove the bell wire from the Wall Control terminals and operate from the remote control only. If this solves the problem, the Wall Control is faulty (replace), or there is an intermitt

28 Adjustment Step 2 Adjust the Force Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door. The door will stop in the up direction if anything interferes with its travel. The door will reverse in the down direction if anything interferes with its travel (including binding or unbalanced doors). If the forces are set too light, door travel may be interrupted by nuisance reversals in t

If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. To avoid installation difficulties, do not run the opener at this time. To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. Do NOT use an extension cord, 2-wire adapter, or change the plug in any way to make it fit your outlet. Right Wrong If permanent wiring is required by your local code, refer to the following pro

Attach sprocket cover securely. Never operate opener Dispensing Carton while your hand is near the opener sprocket. Opener Sprocket Figure 2 Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Keep Chain and CabIe Taut When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag. See master link procedure, Figure 1. • With the trolley against the screwdriver, dispense the cable around the pulley. • Proceed back aroun

Fasten the manual near the garage door after installation. Complies with UL 325 /11 ii "N_ regulations effective January !, 1993 I:RRFTSMRNo 1/2 HP GARAGE DOOR OPENER • Safety Precautions • Assembly • Installation • Adjustment • Care and Maintenance • Operation • Troubleshooting • Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Contents Page Contents Page A review of safety alert symbols ................................. 2 Install the light and lens ..........................

All the codes the opener has learned will be erased. • To reprogram, repeat Steps 1, 2 and 3 for each remote control in use. Replacement Parts: 12 Volt battery -10A14; Compact remote control case, cover and Velcro strip (circuit board not included) - 41A3592; 3-Function remote control case, cover, screw (circuit board not included) - 41A3888; Visor Clip - 29C128 Select a remote control push button to operate opener Figure 2 Garage Door Opener (With Green "SRT" Button) [ M Су Çy / \ |7i

Secure the bracket as shown in Figure 1 if there is vertical reinforcement. If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2. HeaderBraokel Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, doors with ure 2 24 Figure 1 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They app

• Any repair to or adjustment of the garage door (including springs and hardware). • Any repair to or buckling of the garage floor. • Any repair to or adjustment of the opener. Without a properly installedsafetyreversalsystem, persons(particularlysmall children)couldbe SERIOUSLYINJUREDor KILLEDby a closing garage door. • Safetyreversalsystem MUSTbetested everymonth. • Ifonecontrol(forceortravellimits) isadjusted,the othercontrol mayalsoneedadjustment. • Nter ANYadjustmentsare made,the safetyreve

For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2). 1. Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door control by color: white to 2 and white/red to 1. 2. Door Control Button: Fasten securely with 6ABx1-l/2" screws. Console Model: Pry off cover along one side witha screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4" self-tapping screws (standard installation) or 6-32x1" machin

Fasten the manual near the garage door after installation. Periodic checks of the opener are required to ensure safe operation. Leer y seguir todas las reglas de seguridad y las instrucciones de operacibn antes de usar este producto por primera vez. Guardar este manual cerca de la puerta de la cochera. Se deben realizar revisiones peribdicas del abridor de puertas para asegurar su operacibn segura. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A TABLE OF CONTENTS Introduction 2.7 Safety