Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS

See Fig. 4. Replace the pushbutton wiring and tighten the screws. Be certain the antenna wire is hanging down vertically and the receiver terminal numbers printed on the receiver case match the numbers on the operator terminal strip. (1) D. Model 8832 - Double Door Garage 3 2 1 3 2 1 3 2 1 3 2 1 (2) (1) E. Model 8833 - Three Door Garage (1) (3) (2) 3 2 1 3 2 1 3 2 1 FIGURE 5 104388 B. If the operating distance drastically decreases, remove the battery access door See Fig. 1A, and replace the bat

A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Rece

In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after July 1, 1998. For Information: Phone 610-873- 6900 info@allstarcorp. com FAX 610- 873-6953 all

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 35 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. B. If the transmitter doesn’t activate the operator, check the coding switches on both the transmitter and receiver to assure an “exact” match. ( See Fig. 2 & 3) . This may necessitate a reprogramming of a Quik Code Classic transmitter to match the receiver coding swi

The radio frequency of the remote controls is fixed and tuned at the factory; adjustments are not required and should not be attempted by the end user. WARNING Keep transmitters and remote controls out of the reach of children. Do not let children play with or use the transmitter or remote controls. Unexpected door operations can cause personal injury or property damage. Do not place transmitter where the buttons can be accidentally or unintentionally activated. Features of the Quik-Code Wireles

Disconnect the power from the opener before removing cover and cutting the jumper. MAKE SURE YOU DISCONNECT THE POWER BEFORE CUTTING THE JUMPER. THE RUN TIMER WILL NOT CHANGE IF THE JUMPER IS CUT WITH THE POWER CONNECTED. This jumper is located under operator cover on the control board, as illustrated. 110057-2 Cut and Separate IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTRUCTIONS! • Ensure authorized personnel only operate the door.

Manually raise the door to its high arc position and temporarily clamp in that position. With the door in this high arc position, measure the distance from the top of the door to the floor (see figure at left). Subtract the actual door height from the high arc distance to the floor. This is the high arc rise of the door. Unclamp and close the door. Using the table below, draw a horizontal line at the appropriate height above the door to intersect with the vertical centerline. 110049 1/2” Above H

To assemble, screw the door arm rod into the the door arm tube in a clockwise direction approximately ten turns. Connect the door arm assembly into the trolley with the open end of the rod Trolley (Close Limit Position) hook facing the power head unit (away from the door). Extend the manual release cord (connected to the trolley) and thread through the warning tag and red pull knob handle. Adjust so the knob is 6 feet above the floor and secure Cushion Arm with a double overhand knot in the end

“OFF-ON” will prevent inadvertent operation of the door from any other push button, radio or keyless entry device. It will also as additional protection from unwanted operation during absence of the owner. This feature is to be activated only when the door is at the full open or close position and never while the door is moving. 2. “LIGHT” button allows the convenience light to be turned on and stay on until turned off by a second push of the button or activation of the door cycle. 3. “UP/DOWN”