Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Allstar Products Group Dateigröße: 1.12 mb Dateiname: Unterrichtssprache:

To assemble, screw the door arm rod into the the door arm tube in a clockwise direction approximately ten turns. Connect the door arm assembly into the trolley with the open end of the rod Trolley (Close Limit Position) hook facing the power head unit (away from the door). Extend the manual release cord (connected to the trolley) and thread through the warning tag and red pull knob handle. Adjust so the knob is 6 feet above the floor and secure Cushion Arm with a double overhand knot in the end of the release cord. Assembly Release the trolley (leave door arm attached) with the manual release cord 110053-2 and pull trolley toward the door. C: INSTALLING THE OPERATOR Step 9: Connecting the Door Arm to the Door Type 1: Door Mounted Bracket Visually align the door arm connecting hole with the middle hole of the door bracket by rotating the tube section in the appropriate direction. Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counterclockwise (increasing the exposed length of the door rod) to provide a cushion when the door is closed or encounters an obstruction. Align connecting hole in the door arm to middle hole in the door bracket; insert 3/8” diameter bolt and tighten locking nut, allowing for free pivot of the arm. Note: Do not overtighten locking nut as this will cause binding between the door arm and door bracket. Type 2: Strut Mounted Bracket Visually align the door arm connecting hole with the connecting pin of the strut by rotating the tube section in the appropriate direction. Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counterclockwise Alternate Strut (increasing the exposed length of the door rod) to provide a cushion Connecting Bracket when the door is closed or encounters an obstruction. Align connecting hole in the door arm with the strut mounted connecting bracket. Insert connecting pin through the hole in the door arm. Cut to Fit Secure the connecting pin to the strut bracket according to the manufacturer’s instructions. Note: Door Bracket Mount or Strut Mount - If rod bottoms in cushion tube, cut rod to allow for proper function of this assembly. 10 11 Step 12: Install a Rough Service lamp bulb (75 Watt maximum) firmly in the light socket. Light bulbs in Door Openers are subject to vibration during normal operation which may shorten their life spans. Rough Service bulbs, available at most hardware stores, are recommended. Fit Light Diffuser tabs into the panel tabs as shown. Clips 110051-3 C: INSTALLING THE OPERATOR STEP 11: Connecting The Electrical Power Consult the label on the rear panel of the Opener to determine its proper working voltage. Normally it will be marked for 115V, 60 cycle operation. (If it is an export model designed for 220V, 50 cycle operation, the label will clearly indicate this.) The Opener must be plugged into a properly grounded receptacle within 3 FT of the Power Unit. A GFI Type receptacle is recommended. Do not use 2-prong adapters and do not use extension cords for anything more than temporary hook-up and testing purposes. Receptacle wiring should be No. 14 or heavier, and must be in compliance with local building and electrical codes. If local codes require permanent wiring, a GFI type circuit breaker is recommended to protect the line. Remove the Strain Relief Bushing and withdraw the Line Cord from the rear of the Power Unit to expose the three insulated connectors. Cut the wire at the rubber jacket of the Line Cord and wire in permanently, employing proper wiring practices. Discard Strain Relief. It is not used with permanent wiring. Using the two wires (black & white) that were left when you cut off the line cord, splice in the permanent connections. Permanent Wiring Connection Normal Connection Ground Wire 110053-1 Step 10: Connecting the Door Arm to the Door - ONE PIECE DOORS (USING OPTIONAL ONE PIECE DOOR ARM ASSEMBLY) Attach door arm brackets to the top surface of the door on the center line. Reposition Open and Close limit stops so trolley stops in locations as shown. Assemble the door arm by screwing curved rod into straight tube section. Allow approximately 6” of rod to project outside of the straight tube. Release trolley with red knob handle and move to a convenient position between Open and Close limits. Connect curved rod section to trolley. Slide door arm and trolley toward door; connect the tube assembly to the door bracket with the 3/8” diameter bolt and locking nut, tightening enough to allow for door arm pivot. Do not overtighten the locking nut. Press door control button and run opener through full open and close cycles, adjusting the limit stops as required to fully open and close the door. At full closed position, the door arm assembly should compress approximately one inch. 110055-1 Closed Limit ...

Herunterladen

Geben Sie zwei Ziffern: