Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
MOUNT THE SENDING UNIT (UNIT WITHOUT LED) ON THE SIDE WHICH IS EXPOSED TO THE MOST SUN. SUNLIGHT MAY AFFECT THE SAFETY SENSORS, AND THIS ORIENTATION WILL HELP REDUCE THE EFFECT. c. Attach the sending and receiving safety sensors to the “U” brackets by inserting all three tabs into the respective holes. Wall Mounting Bracket 5” Washer Nut 1/4”-20 x 1/2” Carriage Bolt 5/16” x 1-1/2” Lag Screw Door Jam U-Bracket Wall Mounting Bracket Receiving Unit LED a c b 11 Wired Infrared Safety Sensor Installation Tools Needed: Ratchet Wrench Tape Measure Power Drill 3/16” Drill Bit 7/16” Socket Driver 7/16” Wrench Pencil IMPORTANT: BOTH WALL BRACKETS MUST BE MOUNTED AT THE SAME HEIGHT FOR PROPER ALIGNMENT. Note: Use Steps a-c for installing sensors on both sides of the garage door. a. Select and mark with a pencil, a mounting location no more than 5 inches above the floor to center line of wall mounting bracket. The safety sensors should be mounted as close to the door track or inside edge of the door as possible to offer maximum entrapment protection. It is very important that both wall mounting brackets be mounted at the same height for proper alignment. b. Drill pilot holes, using a 3/16” drill bit. Using two 5/16” x 1-1/2” lag screws, permanently mount the wall mounting brackets to both door jambs. In some installations it may be necessary to attach a wooden spacer to the wall to achieve the required alignment. Attach the “U” brackets to the wall mounting brackets with 1/4”-20 x 1/2” carriage bolts, washers and nuts. Insert the bolts from the inside of the “U” bracket and hand-tighten. IMPORTANT: IDENTIFY WHICH SIDE OF THE GARAGE DOOR IS EXPOSED TO THE MOST SUNLIGHT. MOUNT THE SENDING UNIT (UNIT WITHOUT LED) ON THE SIDE WHICH IS EXPOSED TO THE MOST SUN. SUNLIGHT MAY AFFECT THE SAFETY SENSORS, AND THIS ORIENTATION WILL HELP REDUCE THE EFFECT. c. Attach the sending and receiving safety sensors to the “U” brackets by inserting all three tabs into the respective holes. Wall Mounting Bracket 5” Washer Nut 1/4”-20 x 1/2” Carriage Bolt 5/16” x 1-1/2” Lag Screw Door Jam U-Bracket Wall Mounting Bracket Receiving Unit LED a c b Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at 10 12 Installation of Wiring for Wired Infrared Safety Sensor Tools Needed: Hammer Uncoil the wires from the infrared safety sensors and route the wire up the garage wall across the ceiling and down to the back of the opener. Tack the wires in place using staples (Not Supplied). Take care to run the wires in a location where they will not interfere with the operation of the door and do not staple through wire. NOTE: If wires must be lengthened or spliced into pre wired installation, use wire nuts or other suitable connectors. To Opener Wire to Opener 13 Connecting Wired Infrared Safety Sensor to Opener Tools Needed: Phillips Head Screwdriver Connect infrared safety sensors to the opener as shown. Shorten wires as necessary and separate wire ends. Strip about 1/2” of insulation off each wire, being careful not to nick wires, and attach wires to the proper terminal screws, then tighten securely, using phillips head screwdriver. One wire has marking on it (numbers, black stripe, etc). Be sure to observe polarity. Apply tension to external wires to test for secure connection. Check that the wires are stapled in place properly. P.B. COM OBS Sending Unit Black Strip Receiving Unit Solid Color Right Side Of Opener LED Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at 11 14 Connecting Opener To Outlet Tools Needed: None TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT CHANGE THE POWER CORD IN ANYWAY. IMPORTANT: THE OPENER MUST BE CONNECTED TO A PROPERLY GROUNDED 3 PRONG, 120 VOLT OUTLET. The opener can be permanently wired. To permanently wire the unit, see permanent wiring option on page 20. Plug the power cord into the closest grounding type receptacle. Excess power cord length must be routed and contained safely away from any moving parts. As soon as power is applied to the opener, the light on the opener will blink once to indicate a successful self-check of the controls. WARNING Outlet Power Cord 15 Connecting Trolley To Latch Assembly Tools Needed: None Slide the trolley until it snaps onto the latch assembly. Attach warning label to the red release cord. Thread the red release cord through the pull knob s...
Dieses Handbuch ist für folgende Modelle:Safety Gate - PRODRIVE 3220C (4.85 mb)
Safety Gate - PRODRIVE 3220C-Z (4.85 mb)
Safety Gate - PRODRIVE 3221C (4.85 mb)
Safety Gate - PRODRIVE 3221C-Z (4.85 mb)