Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Wayne-Dalton Dateigröße: 909.07 kb Dateiname: Unterrichtssprache:

Using a ratchet wrench with a 5/8” (16mm) socket (NOTE: A 3” (76mm) extension is also recommended for added clearance from the horizontal angle), wind the spring by rotating the winding shaft counter clockwise, while watching either the black tooth on the ratchet wheel or the mark on the winding shaft. Important : paw l knob must be in upper position to add/ remove required number of spring turns. After 2-3 turns, remove the ratchet wrench and adjust the cable on the left side. Ensure counterbalance cables are in the first and second grooves of the cable drums in step, Cable Adjustments. Note : Single spring applications require no spring winding on the left hand side, but cable tension needs to be adjusted. Important : Counterbalance cable tension must be equal on both sides prior to fully winding springs. See the spring turn chart for the required number of turns: For single spring applications: Return to the right hand end bracket and continue winding the spring to the required number of turns for your door. Place pawl knob in lower position. For double spring applications: Either use the black tooth on the ratchet wheel for winding reference or place a mark on the winding shaft and end bracket. Place the ratchet wrench with 5/8” socket onto the left hand winding shaft end. To wind the spring, rotate the winding shaft clockwise, while watching the 5 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at black tooth on the ratchet wheel or the mark on the winding shaft. Rotate the winding shaft to the required number of turns for your door. Then return to the right hand side and wind the right hand spring to the required number of turns. Place pawl knob in lower position on both sides. Important : Mark number of spring turns on TorqueMaster® Plus end bracket war ning tag . Note : Since total turns to balance door can deviate from spring turn chart values by ± 1/2 turn, adjustments to the recommended number of turns may be required after rear supports are installed. Important : Hold the door down to prevent it from rising unexpectedly in the event the spring was over-wound and cautiously remove vice clamps from verti - cal tracks. Ratchet wrench with 3” extension and 5/8” socket End bracket Winding shaft Marks Black tooth on ratchet wheel Pawl knob in lower position Pawl knob in upper position SPRING TURN CHART DOOR HEIGHT SPRING TURNS 6’-0” 14 6’-3” 14-1/2 6’-5” 15 6’-6” 15 6’-8” 15-1/2 6’-9” 15-1/2 7’-0” 16 7’-3” 16-1/2 7’-6” 17 7’-9” 17-1/2 8’-0” 18 Securing Drum Wraps 26 Tools: Step Ladder Un-snap the drum wrap hinged latch and rotate down. Important : Pull the counterbalance cable away from the header to clear the latch , while simulta neously sliding the drum wrap against the last rib until the three catches engage the 3rd rib. Re-engage the hinge latch by rotating upward until a distinct snap is felt. Confirm the catch is fully engaged by lightly tugging on it. Repeat for the other side. Rear Support Tools: Ratchet wrench, Socket: 1/2”, 5/8”, Wrench: 1/2”, 5/8”, (2) Vice clamps, Tape measure, Level, Hammer, Step Ladder 27 Raise the door until the top section and half of the next section are in a horizontal position. Do not raise door any further since rear of horizontal track is not yet supported. WARNIING Raising door furt her can result in door falling and ca use severe or fatal injury. Clamp a pair of vice clamps on the vertical tracks just above the second roller on one side, and just below the second roller on the other side. This will prevent the door from raising or lowering while installing the rear support. Using perforated angle (may not be supplied), (2) 5/16”-1- 5/8” hex head lag screws and (3) 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”-18 x 1 hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door within 3/4” to 7/8” maximum of door edge. NOTE: If an idrive® opener is installed, position horizontal tracks one hole above level when securing it to the rear supports. WARNIING Keep horizontal track parallel and within 3/4” to 7/8” maximum of door edge, ot herwi se door could fall, resulting in severe or fatal injury. Important : Do not support the weight of the door on any part of the horizonta l track hanger that cantilevers 4” or more beyond a sound framing member. Note : If rear supports are to be installed over drywall, use (2) 5/16” x 2” hex head lag screws and make sure lag screws engage solid structural lumber. Note : 26” angle must be attached to sound framing members and nails should not be used. Now, permanently attach the weather seal on both door jambs and header (temporarily attached in Preparing the Opening, in the pre-installation section of this...

Herunterladen

Geben Sie zwei Ziffern: