Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Air King Dateigröße: 68.18 kb Dateiname: Unterrichtssprache:

NOTE: ALL HARDWARE REFERRED TO IN THE INSTRUCTIONS MAY BE FOUND IN THE SUPPLIED PARTS BAGS. BASE ASSEMBLY (Figure 1) 1. Place Base on floor. 2. Fit Mounting Flange through large hole in center of Base. 3. Insert (4) 3/8-16 X 1” Carriage Bolts through Mounting Flange and Base. 4. Tilt Base and secure one Carriage Bolt at a time by first putting on a 3/8” Split Lockwasher and then a 3/8-16 Hex Nut. DO NOT FULLY TIGHTEN AT THIS TIME. Repeat above procedure with remaining Bolts. 5. GO BACK AND FULLY TIGHTEN each Hex Nut so that the Flange is securely assembled to the Base. 6. Thread the 3/8-16 X 3/4” Set Screw into the Mounting Flange. Carraige Bolts (4) Set Screw Mounting Flange Base Hex Nut (4) Split Lockwasher (4) Figure 1 New 3/04 MOTOR & COLUMN ASSEMBLY (Figure 2) 1. Remove motor from foam, place on a stable level surface on its side with the oscillation shaft facing upward. 2. Slide flat section on Upper Tube of Column Assembly inside Motor Mounting Bracket Slot. Align the 1/2" diameter Hole in the flat section on the Upper Tube of Column Assembly with the 1/2" diameter Hole in the Motor Mounting Bracket. 3. Insert the 1/2" diameter x 1" long Hex Bolt (3/4" head) through the Motor Bracket, and the Upper Tube Assembly. Place 1/2" diameter Split Lockwasher then 1/2" diameter Nut (3/4" hex) and tighten fully with 2 Adjustable Wrenches. NOTE: Secure these parts before continuing to the Column/Base Assembly section. 4. Insert one 1/4-20 x 1 3/8" Carriage Bolt through the Arc-Shaped Slot in Motor Bracket and Hole in Upper Pipe of Column. To Fasten: Place one 1/4" Flatwasher, one 1/4" Internal Tooth Lockwasher, a second 1/4" Flat Washer and then tighten the Ad 2 5084415 GRILL AND BLADE ASSEMBLY (Figures 3 and 4) 1. Loosen knob, tilt fan head back halfway, retighten knob. 2. Put rear grill onto motor, Lining up the six holes in the grill with the six threaded holes in the mounting flange. Install six 10-32 x 5/16 hex bolts through the grill into the mounting flange. Securely tighten all bolts. 3. Loosen knob and return head to a vertical postion. Retighten knob. 4. Push fan blade onto motor shaft, center hub facing away from motor, until it stops against shaft. Align bolt head set screw with flat of the motor shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely tighten set screw could result in damage to the fan and/or personal injury. 5. Hold the front grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten front grill to rear grill by sliding the hooked wires on the front grill over the Outermost Ring on the rear grill. (Figure 4-Detail A) New 3/04 OPERATING INSTRUCTIONS 1.)TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor: First pull: High Second pull: Medium Third pull: Low Fourth pull: OFF NOTE: This fan is very heavy. Failure to securely hold onto head assembly while adjusting head height or head a...

Herunterladen

Geben Sie zwei Ziffern: