Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Genie, modell INTELLIG 1000 3024H

Hersteller: Genie
Dateigröße: 11.3 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

• Test again. Repeat as necessary until door reverses upon contacting board. WARNING A moving door can cause serious injury or death. 1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including wall console, remote, or wireless keypad. 3. During programming, door opener could begin to run, so stay away from moving door and its parts. On Wall Console PRESS and RELEASE DOOR OPENS PRESS and RELEASE Once the Contact Reverse Testing is complete continue with Programming Remotes on the next page. ©2010 The Genie Company 12/2010 9 PROGRAM SET — + PROGRAM SET — + 2 PROGRAM INTELLICODE® 2 REMOTE TO POWERHEAD FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM PRESS and HOLD SEE BOTH Blue LEDs come ON SEE round Blue LED come ON SEE long Purple LED flashing RELEASE 1 2 3 4 5 6 7 The next press of the remote will operate door. Repeat as necessary for other remotes. Bring remote(s) to powerhead location. Begin with Step 1 and continue through Step 7 for each button to be programmed. NOTE: The following instructions are for the remote(s) provided with this opener. This remote is preset for use with the IntelliCode® 2 Access Security System. Refer to page 16 for additional information on IntelliCode® 1 and 2 remotes and how to switch from IntelliCode® 2 to IntelliCode® 1. See page 10 for programming instructions using IntelliCode® 1 remotes. PRESS and RELEASE PRESS and RELEASE PRESS and RELEASE Basic powerhead programming is complete. Your garage door opener is ready to use. WARNING A moving door can cause serious injury or death. 1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including wall console, remote, or wireless keypad. 3. During programming, door opener could begin to run, so stay away from moving door and its parts. SEE both LEDs OFF SEE both LEDs flash Blue PRESS and RELEASE SEE both LEDs flash Purple ©2010 The Genie Company 12/2010 OPTIONAL PROGRAMMING POWERHEAD TO Homelink®, Car2U®, or IntelliCode® 1 REMOTES and IntelliCode® 1 WIRELESS KEYPADS To complete any of these tasks you MUST have at least one Genie® IntelliCode® 2 remote button already programmed to the powerhead present. For Homelink® or Car2U®: You must also have your Homelink® or Car2U® enabled vehicle present and their programming instructions to perform these programming steps. For Genie® IntelliCode® 1 remote: You must also have your Genie® IntelliCode® 1 remote present. For Genie® IntelliCode® 1 wireless keypad: You must also have your Genie® wireless keypad installed and a PIN already programmed into the keypad. Programming instructions for Genie® IntelliCode® 2 wireless keypad will come with the wireless keypad. Homelink® programming If your Homelink® has been previously programmed to an Genie® opener begin with Step 1 and continue through Step 5 and 6 of the Homelink® section below. If your Homelink® has not yet been linked to a Genie ® opener then go to page 16 and change one remote button from IntelliCode® 2 to IntelliCode® 1, then program that button with the car Homelink® using Homelink® instructions and repeat steps 1-4 then continue with Homelink® steps 5-6. PROGRAMSET— + PROGRAMSET— + PRESS and HOLDSEE BOTH Blue LEDscome ON SEE oneBlue LEDcome ON PRESS and release a previously programmed Genie® IntelliCode® 2 remote button on remote. If you are unsure which remote you have see page 16. Remote must be IntelliCode® 2 enabled. RELEASE 1 2 3 4PRESS andRELEASESEE long Purple LED flashing SEE both LEDsflash Purple IntelliCode® 1 remote or wireless keypad programming Genie® IntelliCode® 1 remote 56 On the IntelliCode® 1 remote PRESS a button and RELEASE. SEE long LED come ON Purple. On the IntelliCode® 1 remote PRESS the same button and RELEASE.SEE both LEDs on the powerheadcome ON Blue. The next press of the remote will operate door. 7 Test. Repeat as necessary for any other IntelliCode® 1 remotes. Genie® IntelliCode® 1 wireless keypad 56789 Enter your wireless keypad PIN. Press and hold button 1 second then release and see on powerhead long LED come ON Purple. Press and hold button 1 second again then release and see on powerhead both LEDs flash Blue. Press and hold button again and opener will activate Wait 30 seconds, enter pin and press button to verify operation. Homelink® or Car2U® programming 56 PRESS the Homelink® button twice. Test. Repeat as necessary for any other pre- programmed Homelink® enabled vehicle. For Car2U® enabled vehicles follow the Car2U® instructions. Test. Repeat as necessary for any other Car2U® enabled vehicle. 56 All optional Your garage door to Release Handle Poignee de deverrouillage Palanca de liberacion POWER HEAD TETE DE PUISSANCE CABEZA DE LA ENERGIA Power Cord Cordon de secteur Cable electrico Door Arm Bras de la porte Brazo de la puerta Header Bracket Embase support Soporte del travesano Clevis Pin, Long Axe de chape, longue Pasador de grillete, largo Clip Etrier Abrazadera Engage chain or belt bullet to Ca...