Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
To obtain a better bass reproduction, we recommend you to install the woofer on a solid floor where the resonance is unlikely to occur. You can obtain a sufficient heavy bass reproduction from a single woofer. However if you use a couple of the woofers, you can obtain an even more effective heavy bass reproduction. Notes • Always install the woofer vertically, keeping a few centimeters from away the wall. • Do not place an object on the woofer or sit on it. • If the woofer is installed in the center of a room, the bass could be extremely weakened. This is due to the influence of the standing wave of the room. If this happened, move the woofer away from the center of a room or eliminate the cause of the standing wave, by installing a bookshelf on the wall, etc. 4GB Getting Started Hooking Up the System Overview Use the LINE IN jacks or the SPEAKER IN terminals of the woofer when you connect the amplifier. • If your amplifier has one of the following types of output jacks, connect the LINE IN jack and the amplifier’s jack using the supplied audio connecting cord. — MONO OUT jack — MIX OUT jack — SUBWOOFER output jack(s) — SUPER WOOFER output jack(s) • If your amplifier does not have the above mentioned output jacks, connect the speaker terminals of the amplifier to the SPEAKER IN terminals instead. IN OUT OFF AUTO LINE L POWER SAVE R LINE IN SPEAKER IN Before you get started • Turn off the power of the amplifier and the woofer before making any connection. • Use the audio connecting cords that are supplied to the respective equipment. If there are not enough audio connecting cords to make the necessary connections, you need to purchase some optional audio connecting cords. • Be sure to make connections firmly to avoid noise. • Connect the AC power cord from the woofer to a wall outlet. • You cannot connect the CENTER output jack for use with Dolby Pro Logic function to the woofer. Bass sound is not output with some Dolby Pro Logic modes. (continued) 5GB Getting Started Connecting to an amplifier with a single set of speaker terminals If your amplifier is equipped with a single set of speaker terminals, connect the woofer to the amplifier, and then connect the front speakers to the woofer. What cords will I need? Speaker cord (supplied) (1 for each speaker) Twist the stripped ends of the cord about 15 mm. Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass. It is useful to decide that the speaker cord marked with a line is always the negative (–) and should be connected to the negative (–) terminal to avoid any improper connections. Hookups 1 Connect the woofer to the amplifier. Connect the SPEAKER IN terminals of the woofer to the amplifier’s speaker terminals with the speaker cords. Be sure to connect both L and R channels. l: signal flow Amplifier This woofer SPEAKER IN OUT L SPEAKER R L R 2 Connect the front speakers to the woofer. Connect the speakers to the speaker terminals of the woofer. This woofer SPEAKER IN OUT Front Speaker (R) L R L R Front Speaker (L) 6GB Connecting to an amplifier with double (A + B) sets of speaker terminals If your amplifier has double (A + B) sets of speaker terminals, connect both the woofer and the front speakers to the amplifier. What cords will I need? Speaker cord (supplied) (1 for each speaker) Twist the stripped ends of the cord about 15 mm. Hookups 1 Connect the front speakers to the amplifier. Connect the speakers to your amplifier’s speaker terminals (A). Amplifier SPEAKER A Front Speaker (R) Front Speaker (L) 2 Connect the woofer to the amplifier. Connect the SPEAKER IN terminals of the woofer to the amplifier’s speaker terminals (B) using speaker cords (supplied). Amplifier This woofer SPEAKER B IN OUT L SPEAKER R L R When using the double (A + B) sets of speakers, make sure that you select the “A + B” position with your amplifier. Note When you are using speaker terminal (A) only (front speaker only) or when the power of the amplifier is turned off, turn down the volume or turn off the power of the woofer otherwise, hum noise may be heard. Getting Started Connecting to an amplifier with a special jack for a subwoofer If your amplifier has a special jack for a subwoofer (like a MONO OUT jack, MIX OUT jack, SUBWOOFER jack or SUPER WOOFER jack), connect the LINE IN jack of the woofer to one of those jacks. What cords will I need? Audio connecting cord (supplied) (1) Hookups Connect the MONO OUT jack of your amplifier to the LINE IN jack of the woofer with the supplied audio connecting cord. Amplifier This woofer LINE IN OUT MONO OUT Note If the output level of your amplifier is not large enough, the sound may not be loud enough. In this case, connect the speaker terminals of the amplifier directly to the SPEAKER IN terminals of the woofer. When using two or more subwoofers Amplifier MONO OUT LINE LINE IN OUT IN OUT This woofer Another woofer Conn...