Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
P. ush and hold ELECTRONIC IGNITION button until the burner Lighting instructions are continued on the next page 11 Ignitor Lighting (continued) 8. For grills equipped with ELECTRONIC IGNITION ateach burner: Repeat steps 4 through 6 to light each burner. 9. Once each burner has ignited, turn knobs to desired setting. WARNING Turn controls and gas source or tank OFF when not in use. CAUTION If ignition does NOT occur in 5 seconds, turn theburner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite withthe valve open, gas will continue to flow out of theburner and could accidently ignite with risk of injury. Match-Lighting s Do not lean over grill while lighting. 1. Open lid. Turn ON gas at LP cylinder. 2. Place match into match holder (hanging from side panel ofgrill). Light match; then light burner by placing match through the cooking grate into firebox. 3. Push in and turn far right or far left burner knob to the HI position, depending on match light hole selected. Be sureburner lights and stays lit. 4. Light adjacent burners in sequence by pushing knobs in and turning to the HI position. Sideburner Ignitor Lighting s Do not lean over grill while lighting. 1. Open sideburner lid. Turn ON gas at LP cylinder. 2. Turn sideburner knob to the HI position, push and holdELECTRONIC IGNITOR button. 3. If sideburner does NOT light within 5 seconds, turn knob to OFF, wait 5 minutes, then repeat lighting procedure. Sideburner Match Lighting 1. Open sideburner lid. Turn ON gas at LP cylinder. 2. Place lit match near burner. 3. Turn sideburner knob to the HI position. Be sure burner lights and stays lit. Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotateknobs from HI to LOW. You should see a smaller flame in LOW position than seen on HI. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" inthe Troubleshooting Section. HI LOW Turning Grill Off • Turn all knobs to the OFFposition. Turn LP cylinder OFF by turninghand-wheel clockwise to a full stop. Ignitor Check • Turn gas off at LP cylinder. Press and hold electronic ignitorbutton. "Click" should be heard and spark seen each timebetween each collector box or burner and electrode. See "Troubleshooting" if no click or spark. Valve Check • Important: Make sure gas is off at LP cylinder before checking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should springback. If knobs do not spring back, replace valve assemblybefore using grill. Turn knobs to LOW position then turn back toOFF position. Valves should turn smoothly. Hose Check • Before each use, check to see if hoses are cut or worn. Replace damaged hoses before using grill. Use onlyvalve/hose/regulator specified by manufacturer. General Grill Cleaning • Do not mistake brown or black accumulation of grease andsmoke for paint. Interiors of gas grills are not painted at thefactory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brushon insides of grill lid and bottom. Rinse and allow to completelyair dry. Do not apply a caustic grill/oven cleaner to paintedsurfaces. • Plastic parts: Wash with warm soapy water and wipe dry. s Do not use citrisol, abrasive cleaners, degreasers or aconcentrated grill cleaner on plastic parts. Damage to andfailure of parts can result. • Porcelain surfaces: Because of glass-like composition, mostresidue can be wiped away with baking soda/water solution orspecially formulated cleaner. Use nonabrasive scouring powder for stubborn stains. • Painted surfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth. • Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy waterand wipe dry with a soft cloth after each use. Baked-on greasedeposits may require the use of an abrasive plastic cleaningpad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics. • Cooking surfaces: If a bristle brush is used to clean any ofthe grill cooking surfaces, ensure no loose bristles remain oncooking surfaces prior to grilling. It is not recommended toclean cooking surfaces while grill is hot. Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas OFF at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove carryover tubes and burners. 4. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the one easiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube several times. (B) Use a narrow bottle brush with a flexibl...