Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Cal Flame Dateigröße: 650.46 kb Dateiname: Unterrichtssprache:

Natural Gas Requirements The installation of this appliance must conform with local codes or, in the absence of local codes, to the national fuel gas code, ANSI Z223.1a-1998. Installation in Canada must be in accordance with the standard CAN/CGA-B149.2, Propane Installation Code. A licensed contractor or local gas company representative must perform all natural gas connections. Ensure that the service supplying the side burner is fitted with a shut off valve conveniently positioned near the side burner and giving ease of access. The side burner must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 0.5 psi (3.5 kPa). The side burner and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressure in excess of 0.5 psi (3.5 kPa). Connection Slide the side burner forward to gain access to the gas connection 1. point in the rear. Connect a suitable flex connector to the gas connection point.2. Check the side burner controls to ensure all control valves are in 3. the full OFF position. Turn on the main gas supply and check all connections for leaks 4. using soapy water as described in the leak testing procedure section. Warning: If you see bubbles in the soapy solution at any of the connections, turn off the gas supply and tighten the connection. If tightening the connection does not seal the leak, it may be necessary to replace the flex hose. Installing Side Burner with a Grill If you are installing a side burner in conjunction with a gas grill, install it in the following manner. Assemble a 3/8” pipe nipple to the 3/8” pipe tee using Teflon tape 1. or pipe sealant. Use only sealant that is approved for use on LP gas. Install the pipe tee assembly to the grill intake pipe. Tighten as2. sembly and align the branch opening of the tee with the hole of the cabinet. Connect the flexible hose (male end) to the pipe tee.3. Install and secure the side burner into the island by simply setting 4. it in place. Connect the female end of the flexible hose to the side burner 5. intake pipe. Connect gas supply to the grill.6. Check for gas leaks using soap water solution.7. CBABCAConnect the last open line to the side burner (Use gas rated tape sealon all connections) Then take other end of "T" adapter with hose attached and connectto end of male located underneath and at the back of the grill. (Usegas rated tape seal on all connections). Open barbecue door. Install hose with regulator on propane tank. Then connect the other end to "T" adapter. Make sure to use gasrated tape seal when installing adapter to insure proper seal. GrillNOTE: You will need to use a gas rated sealer on gas connectors that are not flared. To Propane Tank3/8" FittingsFrom GrillFrom Side Burner"T" Adapter (3/8" Threaded) To side burner, locatedunderneath behind burner. To grill, locatedunderneath and behind grill Using Your Side Burner Read all instructions before you operate your side burner. We recommend you wash your side burner with soap and water prior to lighting it for the first time. Oils are used during the manufacturing process and some residual oil may still be on the stainless steel parts of your side burner. Washing will reduce the possibility of discoloration. We also recommend you keep your side burner covered when not in use. This will minimize the amount of dust and dirt that accumulates on your side burner and extend the life of your side burner. Remember to use your Cal Flame side burner safely by following these reminders: It is dangerous to use side burners in any manner other than for • what it is designed for. Do not use charcoal in a side burner.• Do not heat sealed containers such as cans or jars on side burners. • Explosion may result resulting in injury or death. Any sealed container, such as a pressure cooker, must have a properly operating pressure relieve valve to minimize explosion hazard. Never put combustible material such as paper, cloth, or flammable • liquids on your side burner at any time. Do not use the side burner to store flammable materials. Lighting the Side Burner Each time you light the side burner, check the following: Inspect the hose before using the side burner. If there is excessive • abrasion or wear, or if the hose is cut, it must be replaced prior to using the side burner. If you need a replacement hose, contact your Cal Flame dealer. Ensure the area around the barbecue is clear of flammable sub• stances such as gasoline, yard debris, wood, etc. Ensure there is no blockage of the airflow through the vent space • located below the face of the unit. When using propane gas:• Keep the special ventilation openings in the enclosure • free and clear of debris. If connected to a propane cylinder, carefully inspect • the rubber hose attached to the regulator before each use. Ensure the p...

Herunterladen

Geben Sie zwei Ziffern: