Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
. This appliance is heavy, care should be taken when moving it. . When moving, do not tip the washing machine onto it.s front or left. hand side (viewed from the front). This is to prevent the possibility of. electrical components becoming wet. . Before installation inspect the machine for transport damage. Do not. connect the appliance if it is damaged . contact your retailer. . Ensure all packaging and transit bolts/bar have been removed, see. .Removing of Transit Packaging.. Failure to remove packaging and. transit bolt/bar may cause serious damage to the product or property. . Any plumbing work required to install this appliance should be car. ried out by a qualified plumber or competent person. . Any electrical work required to install this appliance should be carried. out by a qualified electrician or competent person. . Check the electricity supply is the same as that indicated on the rat. ing plate of the appliance. . Should the appliance mains cable need to be adapted for any reason. this should only be carried out by a qualified/competent person. . In the case of a permanent connection it is necessary that you install. a double pole switch between the appliance and the electricity supply. (mains), with a minimum gap of 3 mm between the switch contacts. and of a type suitable for the required load in compliance with the. electrical regulations. . The switch must not break the yellow and green earth cable at any. point. . Care must be taken to ensure that the appliance does not stand on. the electrical supply cable. . The installation must comply with local water authority and building. regulations requirements. . Appliances designed for cold water connection must not be con. nected to hot water. Installation and Connection Instruction. Appliance Dimension. Front and Side Views. Rear View. Hot Water inle. Cold Water inle. Installation and Connection Instruction. Appliance Installatio. The appliance worktop must not be removed to gain a height reduction. 3 when installing under a kitchen worktop. Appliance Transi. . To prevent electrical components becoming wet when moving the. appliance, do not tip the washing machine onto it.s front or the left. hand side (viewed from the front). . Do not transport the appliance without the transit packaging/bolts. bar in place. Transporting the appliance without the transport pack. aging/bolts/bar in place may cause damage to the product. . Never lift the appliance by the door. . The appliance is heavy, care must be taken when moving it. Installation and Connection Instruction. Removing Transit Packagin. Important! Ensure all transit packaging is removed prior to installation. Retain transit packaging for future use. The appliance is supplied with a spanner (H) and plastic caps (E) (2 pcs.). and (G) (1 pc). 0 1. Remove the hose holder (A). 2. Remove the 2 screws (B) with the spanner supplied (H). 3. Remove the 4 screws (C). 4. Remove the transit bar (D). 5. Cover the holes left by screws (B) the 2 plastic caps (E). Important: When fitting the plastic caps, press until they snap into the. rear panel securely. 6. Replace the 4 screws (C), for safe keeping. 7. Remove the screw and compression spring (F) with the spanner (H),. cover the hole with plastic cap (G). Important: When fitting the plastic cap, press until they snap into the. rear panel securely. Installation and Connection Instruction. Installation-Site Preparatio. . The installation surface must be clean, dry and level. . Do not install on deep pile carpet. . If the appliance is installed next to heat source (e. g. cooking appli. ance), a heat insulating pad (85 x 57 cm) must be placed between the. washing machine and the heat source. . Do not install the appliance in locations where the temperature may. fall below freezing. . Please ensure that when the appliance is installed it is easily accessi. ble for the engineer in the event of a breakdown. Installation on a Suspended Floo. Suspended wooden floors are particularly susceptible to vibration. To. help prevent vibration we recommend you place a waterproof wood. panel, at least 15 mm thick under the appliance, secured to at least 2. floor beams with screws. If possible install the appliance in one of the. corners of the room, where the floor is more stable. Levelling the Applianc. Using the four adjustable threaded feet, compensation can be made for. unevenness in the floor and the height of the appliance adjusted. The. height can be adjusted over the range +10... -. mm.. To adjust the feet use the special spanner supplied for removing the. transport braces.. 0 1. Slide the special key firmly onto the hexagon head of the threaded foot. all the way to the stop.. 2. Adjust the threaded feet so that the appliance is level and stable. The. appliance must not rock across the corners when operating under load.. 3. If necessary, check positioning with a spirit level.. Important! Never use strips or shims of wood or cardboard etc. to. compensate for any uneveness...