Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Cal Flame Dateigröße: 650.46 kb Dateiname: Unterrichtssprache:

Make sure the valve orifice is free of any debris, • dust or grease. If there is no spark at all, replace the electrode or • igniter wire. Note: Turn off the gas at the source while troubleshooting. Problem: Obstruction in the gas line Solution: Remove the fuel line from side burner. (Do not smoke or perform any maintenance in the vicinity of an open flame.) Open the gas valve for one second to blow out any debris. Close off the gas valve and reconnect the fuel line securely. Problem: Yellow Flame Solution: Once the entire burner is operating, check the flame color to be sure that it is mostly blue. Some yellow at the tips may be present due to impurities in the fuel. If the flame is golden or yellow in color, the reason could be oil film, residue from boil over, or other foreign matter on the burner. Problem: Plugged orifice Solution: Unplug the orifice as follows: Remove burner rack and brass burner.• Using a 7mm socket or socket wrench, remove the • brass orifice. Gently clear any obstruction with a fine wire.• Reinstall the orifice and replace the burner racks.• If an obstruction is suspected in the control valve, contact your local Cal Flame dealer for assistance. Problem: Misalignment of Igniter on Burner Solution: Check for proper position of the electrode tip, which • is next to, but does not touch, the brass burner. It should be pointing straight up and free of grease to allow proper sparking. The ignition wire should be connected firmly to the • valve ignition device and electrode. Reattach it if it has become disconnected. Replace the ignition wire if it is frayed or cracked. With the gas supply closed and control knobs set to • the off position, check each position igniter individually for the presence of a spark at the electrode. Push each knob in fully and rotate it about 1/4 turn to the left (counter-clockwise) until you hear a loud click. The trigger hitting the strike block should produce a blue spark at the electrode tip. Return control knob to the off position before checking the next igniter. Converting Side Burner from LP to NG When converting an LP side burner that is connected to an LP grill, you MUST convert both appliances. It is dangerous to have an LP appliance and an NG appliance supplied by the same fuel. WARNING! You must have an authorized service technician perform this procedure. If these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Lloyd’s Material Supply (LMS) will not be held responsible for an improperly converted gas side burner. All Cal Heat side burners are manufactured to use standard liquid propane (LP) and can be converted to burn natural gas (NG). You will need one or two orifices (depending on the size of the side burner), contained in the conversion kit provided with the side burner. The conversion kit contains orifices to convert five main burners, two small rear infrared burners, one large infrared burner, and two side burners. You will not need all of the parts in the kit. Before you begin, make certain the LP gas source has been disconnected. Replacing the side burner orifices Remove the grate, burner cap and burner diffuser from the side 1. burner. Using a 7mm wrench, remove the orifice for the burner.2. Apply a small amount of pipe compound to the orifice threads.3. Screw in the orifice until it is finger tight.4. Tighten the orifice with the 7mm wrench.5. If you have dual side burners, repeat the previous steps for the 6. second burner. Replacement Covers Side Burner Model Cover Part Number Cover Size BBQ08852P Standard Single Flat Side Burner CVRSBR050-G 11” x 17 .” x 5 .” BBQ08953P Standard Side By Side Burner CVRSBR052-G 24 .” x 19 .” x 6 .” BBQ08899P Deluxe Double Side Burner CVRSBR054-G 13” x 23 .” x 10” BBQ08954P Deluxe Double Side By Side CVRSBR055-G 26” x 13” x 10 .” Limited Warranty All Cal Flame models are manufactured with the highest quality appliances and are warranted to be free from defects in material and workmanship at time of delivery. LMS warrants side burners and associated hardware from deterioration, corrosion, and defects in material and workmanship for a period of one year. Extent of Warranty This limited warranty is only valid on Cal Flame models delivered in the United States or Canada and extends through the selling dealer to the original purchaser at the original site of installation. This warranty becomes valid at time of delivery and ends either by specified time-frame listed above or upon owner transfer or relocation. Warranty Performance In the event of a malfunction or defect covered under the terms of this warranty, a factory authorized service agent of LMS will perform the necessary repairs. To obtain service, contact the selling dealer. In the event the consumer is unable to obtain satisfactory customer service from the selling dealer or service agent, written notification must be given to the LMS Customer Relations Department within 30 d...

Herunterladen

Geben Sie zwei Ziffern: