Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Samsung Dateigröße: 2.57 mb Dateiname: Unterrichtssprache:

FRONT LEG COVER Separating the Water Supply Line from the Refrigerator Remove the water tube by pressing the coupler (.) and pulling the water tube (.) away. NOTE Be careful not to cut the water tube when separating it from the coupler. 22 REMOVING THE REFRIGERATOR DOORS Removing the Freezer Door NOTE • Lift the door straight up. • Be careful not to pinch the water tubing and wire harness on the door. • Place doors on a protected surface. 1) With the door closed, remove the upper hinge cover (.) along the arrow (.) using a screwdriver, and then disconnect the wires (.). 2) Remove hinge screws (.) and ground screw (.) counter-clockwise, and take off the upper hinge (.) along the arrow (.). Take care when removing the door to ensure that it does not fall on you. 3) Remove the door from the lower hinge (.) by carefully lifting the door (.). NOTE Be careful not to pinch the water tubing and the wire harness at the bottom of the door. INSTALLATION INSTRUCTIONS 23 REMOVING THE REFRIGERATOR DOORS Removing the Refrigerator Door 1) With the door closed, remove the upper hinge cover (.) along the arrow (.) using a screwdriver. 2) Remove hinge screws (.), and take off the upper hinge (.) in the direction of the arrow (.). Take care when removing the door to ensure that it does not fall on you. 3) Remove the door from the lower hinge (.) by 4) Remove the screw from the bracket lower hinge lifting the door (.). (.) and then remove the lower hinge (.) from the bracket (.) by lifting the lower hinge (.) in the direction of the arrow. 24 REATTACHING THE REFRIGERATOR DOORS Reattaching the Freezer Door 1) Reattach the freezer door by inserting the hose (.) in the lower side of the door into the hole in the lower hinge (.) and pull the hose down. 2) Insert the upper hinge shaft (.) into the hole (.). After leveling between the upper hinge hole and the hole of the cabinet, reattach hinge screws (.) and ground screw (.) in a clockwise direction. 3) Connect the wires. 4) Put the front part of the upper hinge cover (.)on the front part of the upper hinge (.) and reattach from the front part of the upper hinge cover first. 7 8 INSTALLATION INSTRUCTIONS 25 REATTACHING THE REFRIGERATOR DOORS Reattaching the Refrigerator Door 1) Insert the lower hinge (.) in the bracket lower 2) Place the hole in the refrigerator door (.) over hinge (.). the lower hinge (.). 3) Insert the upper hinge shaft (.) into the hole (.). After leveling between the upper hinge hole and the cabinet hole. Reattach hinge screws (.) and gound screw (.) in the clockwise direction. 4) Put the front part of the upper hinge cover (.) on the front part of the upper hinge (.) and reattach it from the front part of the upper hinge cover first. 9 26 REATTACHING THE REFRIGERATOR DOORS Reattaching the Water Supply Line While pressing the front face of coupler (.), insert the water line (.) in the coupler. Reattaching the Front Leg Cover Carefully place front cover and push to snap it into position. FRONT LEG COVER 27 INSTALLATION INSTRUCTIONS 28 ADJUSTING THE HEIGHT BETWEEN THE DOORS The doors will be uneven if the refrigerator is not level. Case 1) Freezer door is lower than the refrigerator door. Insert a flat-blade screwdriver (-) (.) into a slot of the control lever (.), turn it clockwise and level the refrigerator. Case 2) Freezer door is higher than the refrigerator door Insert a flat-blade screwdriver (-) (.) into a slot of the control lever (.), turn it clockwise and level the refrigerator. Do not make small adjustments with the control lever, Please refer to the next page. DIFFERANCE OF HEIGHT DIFFERANCE OF HEIGHT . DRIVER(-) . DRIVER(-) . CONTROL LEVER . CONTROL LEVER Please level the refrigerator first NOTE 29 ADJUST THE HEIGHT BETWEEN THE DOORS Making small level adjustments between doors If the freezer door is lower than the refrigerator door. If the freezer door is higher than the refrigerator door. 3) After adjusting the doors, turn the nut (.) clockwise( ) until the lower end of the bolt, then tighten the bolt again with ...

Herunterladen

Geben Sie zwei Ziffern: