Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
WARNING CARBON MONOXIDE (REFERED TO AS CO) CAN CAUSE PERSONAL INJURY OR DEATH WARNING FAILURE TO FOLLOW THESE INSTRUCTIONS, LOCAL CODES OR NATIONAL CODES MAY CAUSE FIRE, EXPLOSION, ELECTRICAL SHOCK, PERSONAL INJURY OR PROPERTY DAMAGE. FOLLOW ALL LOCAL CODES. IN THE ABSENCE OF LOCAL CODES REFER TO : NATIONAL ELECTRICAL CODE NFPA 70 NFPA 90A & 90B UNIFORM MECHANICAL CODE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS APPLIANCE. ONLY FACTORY AUTHORIZED KITS OR ACCESSORIES SHOULD BE USED WHEN INSTALLING OR MODIFYING THIS APPLIANCE, UNLESS OTHERWISE NOTED IN THESE INSTRUCTIONS. SOME LOCALITIES MAY REQUIRE THE INSTALLER/SERVICER TO BE LICENSED. IF IN DOUBT CONTACT YOUR LOCAL AUTHORITIES. These instructions should be retained and kept adjacent to the unit for future reference. MODEL # HB 00VA1M25 MODEL # HB 00VC1M25 INSTALLATION DATE The information contained in this booklet is subject to change without notice. No. 0010575351 E INDEX TOPIC PAGE General 1 Physical dimensions 2 Replacement Parts Source 3 Installation Requirements 3 Air Flow Orientation 4 Horizontal Left-Hand Instructions 5 Downflow Instructions 6 Refrigerant Tubing 7 Condensate Removal 7 Electrical Connections 8 Thermostat Wiring 9 Orifice Change 11 Circulating Air Duct 11 Blower Performance 12 Start-up 13 Regular Maintenance 13 Model Number Explanation 14 The United States Environmental Protection Agency (EPA) has issued various regulations regarding the introduction and disposal of refrigerants introduced into this unit.Failure to follow these regulations may harm the environment and can lead to the imposition of substantial fines. These regulations may vary due to the passage of new laws, it is recommended that any work on this unit be done so by a certified technician. Should questions arise contact the local EPA office. THIS APPLIANCE IS NOT APPROVED FOR OUTDOOR INSTALLATION THIS APPLIANCE IS NOT TO BE USED AS A CONSTRUCTION HEATER GENERAL This appliance was designed certified and must be installed in accordance with published codes.In the absence of local codes please refer to the following codes: NFPA 90A NFPA 90B National Electrical Code NFPA 70 Uniform Mechanical Code Prior to shipment, this appliance was tested and inspected for damage at the factory.Unpack carefully and if damage is found, report it immediately to the transportation company. This appliance is approved for installation in alcoves, basements, attics or crawlway, and is designed for connection to air distribution ductwork. 2 PHYSICAL DIMENSIONS D C PRIMARY & SECONDARY CONDENSATE DRAINS- HORIZONTAL 3/4" NPT 2" [5.08 cm] 5.1" [13 cm] 2" [5.08 cm] TYPICAL F KG 1.1" [2.9 cm] 5" [12.7 cm] H 2.4" [ 6 cm] 1.2" [ 3 cm] INLET 0.8" [2.1cm] PLASTIC BREAKER COVER B JE 12.2" [31 cm] A SUCTION LINE LIQUID LINE 1" [2.54cm] INLET RIGHT SIDE VIEW FRONT VIEW PRIMARY & SECONDARY CONDENSATE DRAINSUPFLOW 3/4" NPT-FEMALE For: HB3600VC1M25 A B C D E F G H J K 53.3 [135.5cm] 22.1 [56.1cm] 23.5 [59.8cm] 25.2 [64.0cm] 9.1 [23cm] 8.3 [21.2cm] 4.7 [12cm] 22.2 [56.5cm] 19.8 [50.4cm] 3.6 [9.05cm] For: HB42-6000VA1M25 HB6000VC1M25 A B C D E F G H J K 59.4 [151cm] 22.1 [56.1cm] 23.5 [59.8cm] 25.2 [64.0cm] 9.1 [23cm] 8.3 [21.2cm] 4.7 [12cm] 22.2 [56.5cm] 19.8 [50.4cm] 3.6 [9.05cm] 3 REPLACEMENT PARTS SOURCE Replacement parts are available through local distributors.When ordering replacement parts, give the COMPLETE model and serial numbers shown on the rating plate. INSTALLATION REQUIREMENTS Before installing this appliance insure that it is properly sized and adequate power is available. This appliance can be installed in the vertical or right horizontal position without modification. The horizontal left and downflow positions require product modification. This product is designed for zero inch (0") clearance; however, adequate access for service or replacement must be considered without removing permanent structure. This unit can be installed on a platform when deemed necessary. In an attic installation a secondary drain pan must be provided by the installer and placed under the entire unit with a separate drain line properly sloped and terminated in an area visible to the owner. This secondary drain pan is required in the event that there is a leak or main drain blockage. Closed cell insulation should be applied to the drain lines in unconditioned spaces where sweating may occur. Appliances installed in garages, warehouses or other areas where they may be subjected to mechanical damage must be suitably guarded against such damage by installing behind protective barriers, being elevated or located out of the normal path of vehicles. When installed on a base, the base must also be protected by similar means. Heating and cooling equipment located in garages, which may generate a glow, spark or flame capable of igniting flammable vapors, must be installed with the ignition source at least 18" above the floor level. When more than one appliance is installed in a building, perm...
Dieses Handbuch ist für folgende Modelle:Luftreiniger - HB3600VC1M25 (254.88 kb)