Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Sunbeam Dateigröße: 305.5 kb Dateiname: Unterrichtssprache:

3. Experiment with the location and sensitivity and fan speed settings on your unit. If you feel that your home’s air continues to contain allergen particles after running the unit at a low fan speed (sleep, low or medium) or at a lower sensitivity setting (average or extra), try increasing the fan speed to medium or high and/or increasing the sensitivity setting to extra or super. You can also try repositioning the unit in your room. Remember that the higher the sensitivity setting, with super being the highest, the lower the particle count required to cause the unit to turn on. If you feel that the unit is running too often, reduce the sensitivity setting (i.e. change the sensitivity setting from super to extra or average). If you feel that your home’s air needs constant cleaning, for instance during high pollen count days, you should manually operate the unit to run constantly (see page 7 for instructions). 4. Manually turn your air cleaner on if you see, smell or otherwise notice smoke in the air. The Allergysmart sensor does not detect smoke particles in the air due to their small size; however, the Allergysmart air cleaner does reduce smoke particles in the air with a True HEPA filter which will remove particles as small as .3 microns from the filtered air. 5. The AllergysmartTM detector does not sense differences in types of allergy particles. If you are allergic to a particular type of allergen (such as pollens) you may want to adjust the sensitivity setting on your air cleaner because of changes in your home’s air. Caution: Individuals with acute respiratory problems should consult with their physician regarding use of an air cleaner as part of a treatment program. In addition to the AllergysmartTM Allergen Monitor, this Sunbeam air cleaner is equipped with the following features: TRUE HEPA FILTER Certified to capture 99.97% of all contaminants .3 microns or larger. CHARCOAL PRE-FILTER Reduces odors and extends the HEPA filter life. FILTER CHECK REMINDER LIGHTS Reminds you to check to see if your filter needs replacement. IONIZER An added stage of filtration to further clean the room. The ionizer negatively charges small particles not captured by the HEPA filter as they leave the air cleaner. These tiny charged negative particles will combine with other larger positively charged particles that can then be filtered out of the air through the air cleaner. CLEANING CAPACITY Your air cleaner has the capacity to clean the air in a 10’ x 12’ room every 5 (model 2541) or 8 (model 2540) minutes on the high fan speed setting. Your air cleaner has a total of four fan speed settings, including an extra quiet sleep setting. Adjust fan settings as needed. The sleep setting will be the quietest setting but will also be the lowest performing in terms of the capacity of air cleaned. CHECKING THE FILTER ALWAYS UNPLUG THE UNIT BEFORE CHECKING THE FILTER. The check filter light indicates when it’s time to check your HEPA or charcoal filter to see if it needs replacement. If the light is: Blinking Check the charcoal filter for possible replacement (usually 3 months after initial usage). Check the appearance of the filter to see if there is a visible amount of dust or lint on the filter. If so, you will need to replace the charcoal filter with replacement model #6620 for the model 2540 air cleaner, or #6622 for the model 2541 air cleaner. See instructions below for replacing the filter. After you have checked or replaced the filter, make sure to press the RESET button. I mm New In use In use Time to change Solid Check the HEPA filter for possible replacement (usually a minimum of lyear after the initial usage). If the filter appears brown in color, it is time to replace the filter. Use replacement filter model # 6619 for model 2540 air cleaner and #6621 for model 2541 air cleaner. See instructions below for replacing the filter. After you have checked or replaced the filter, make sure to press the RESET button. CHANGING THE FILTER A=Zb 1. Always unplug the unit prior to replacing the filter. 2. To remove the filter, turn the unit upside down and unscrew the knob at the base of the air cleaner. 3. Remove the old filter and replace with a new filter. 4. Replace base of unit and screw knob back in place. 5. Both the HEPA and charcoal filters can be replaced at your local retailer or ordered by mail. (seeenclosedform) NEVER ATTEMPT TO SERVICE OR DISASSEMBLE THE UNIT YOURSELF (other than replacing the filter). 1 Always unplug the unit before cleaning and when not in use. I. 2. Outside surfaces intake or vents can be cleaned with a soft cloth. 3. Do not submerge in water, or allow water to come in contact with the air cleaner. Sunbeam Products, Inc. warrants to the original purchaser, for a period of two years from date of purchase, this product shall be free of mechanical and electrical defects in material and workmanship subject to the limitations and exclusions set forth below. This warranty does not cover normal wear of ...

Herunterladen

Geben Sie zwei Ziffern: