Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Briggs & Stratton Dateigröße: 477.38 kb Dateiname: Unterrichtssprache:

Before installing new filter, lightly oil filter gasket with fresh, clean engine oil. Screw filter on by hand until gasket contacts oil filter adapter. Tighten 1/2 to 3/4 turn more. Start and run engine at idle to check for oil leaks. Recheck oil level and add oil if required. Oil filter OIL FILTER P/N SEE PAGE 8 Air cleaner Dual element air cleaner COVER KNOB COVER CARTRIDGE KNOB CARTRIDGE & PRE-CLEANER 5053 STUD BASE Note: Depending on engine Type Number, this engine may not be equipped with a pre-cleaner. 1. Remove cover knob and cover. 2. Remove cartridge knob. Carefully lift pre-cleaner and cartridge from base over stud. 3. Clean base carefully to prevent debris from entering carburetor. To service pre-cleaner, wash in liquid detergent and water. Squeeze dry in a clean cloth. Saturate in engine oil. Squeeze in clean, absorbent cloth to remove all EXCESS oil. Replace if very dirty or damaged. To service cartridge, clean by tapping gently on a flat surface. Do not oil cartridge. Replace if very dirty or damaged. Pre-cleaner Cartridge PRE-CLEANER 272403 CARTRIDGE 496894 Note: Do not use petroleum solvents, e.g., kerosene, which will cause the cartridge to deteriorate. Do not use pressurized air to clean cartridge. Pressurized air can damage the cartridge. 4. Reassemble pre-cleaner on cartridge and place assembly over stud on base. Tighten cartridge knob. 5. Replace cover and tighten cover knob securely. In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 7 Maintenance See Maintenance Schedule, page 8. Follow the hourly or calendar intervals, whichever occur first. Note that more frequent service is required when operating in adverse conditions. Keep engine and parts clean. Do not clean with a forceful spray of water because water could contaminate fuel system. Rotating screen With a brush or cloth, remove grass, chaff or debris from finger guard or rotating screen daily (more often if needed) to prevent engine damage caused by overheating. Finger guard CLEAN CLEAN Linkage, springs & controls CLEAN To assure smooth operation, keep governor linkage, springs and controls free of debris. If engine muffler is equipped with spark arrester screen, remove for cleaning and inspection. Replace if damaged or plugged. See an Authorized Briggs & Stratton Service Dealer for correct replacement. Muffler and spark arrester Daily or more often, before running engine, clean muffler area to remove all grass and combustible debris. CLEAN CLEAN ARRESTER Grass, chaff or debris may clog the air cooling system, especially after prolonged operation cutting tall, dry grass. Remove blower housing and clean area shown to prevent overheating and engine damage. Clean more often if necessary. Air cooling system CLEAN OUT CHAFF AND DEBRIS .030” (0.76 mm) WIRE GAGE RESISTOR PART NO. 491055 Spark plug Use only Briggs & Stratton Spark Tester, Part No. 19368, to check for spark. Replace spark plug. Do not blast clean. Clean by scraping or wire brushing and washing with a commercial solvent. Note: In some areas, local law requires using resistor spark plug to suppress ignition signals. If this engine was originally equipped with resistor spark plug, use same type for replacement. In-line fuel filter Replace in-line fuel filter. See any Authorized Briggs & Stratton Dealer for correct replacement. PART NO. 394358 (WITH FUEL PUMP) P/N 298090 OR 5018 (WITHOUT FUEL PUMP) FILTER Drain fuel tank or close fuel shut-off valve before replacing fuel filter. Fill in both sides, clip and return to: Briggs & Stratton Corporation P.O. Box 1144 Milwaukee, WI 53201-1144 U.S.A. Your Engine Model Type Code See any Authorized Briggs & Stratton 273683 Service Dealer. Insist on Genuine Briggs & Stratton parts! Non-original parts may not perform as well and may void your warranty. To obtain a complete Parts List of Genuine Briggs & Stratton Parts for your engine, fill in both sides of this order form carefully. We cannot fill your order without the correct Engine Model/Type/Code. (Please allow 3 to 4 weeks for delivery.) Maintenance Schedule Follow the hourly or calendar intervals, whichever occur first. More frequent service is required when operating in adverse conditions noted below. Maintenance Operation Every 8 Hours or Daily 25 Hours or Every Season 50 Hours or Every Season 100 Hours or Every Season...

Herunterladen

Geben Sie zwei Ziffern: