Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
. . 7 locations for valet/program switch...........8 locations for the status LED................8 finding the wires you need....................9 locations for the optional starter kill relay......9 locations for the relay satellite..............9 obtaining constant 12V...................9 finding the starter wire..................10 finding the 12V switched ignition wire........10 finding the tachometer wire...............11 finding the wait-to-start bulb wire for diesels . . 11 finding the accessory wire................11 finding the door pin switch circuit...........12 finding a (+) parking light wire.............12 making your wiring connections...............13 primary harness (H1), 12-pin connector..........14 auxiliary harness (H2), 6-pin connector..........14 door lock harness, 3-pin connector.............15 remote start ribbon harness, wiring diagram.......15 heavy gauge relay satellite wiring diagram........16 remote start harness (H3), 5-pin connector.......16 primary harness (H1) wire connection guide.......17 secondary harness (H2) wire connection guide.....21 relay satellite interface wire connection guide.....23 remote start secondary harness (H3) wire connection guide .....................................25 neutral safety switch interface................26 testing the neutral safety switch............27 bypassing GM vehicle anti-theft systems (VATS)----30 1995 and newer vehicle anti-theft systems (immobilizers) .....................................31 passlock I and passlock II (PL-1 and PL-2).....31 passkey III (PK-3), transponder-based systems . . 31 plug-in LED and valet/program switch...........32 programmer interface, 3-pin black plug..........32 shock sensor harness, 4-pin connector...........33 tach learning............................34 programming jumpers......................34 transmitter/receiver learn routine™.............35 tach threshold on/off...................35 light flash (+)/(-)......................35 transmitter configurations...................37 standard configuration...................37 multi-level security arming...................38 system features learn routine.................39 feature menus............................41 menu #1 - basic features.................41 menu #2 - advanced features..............42 menu #3 - remote start options.............42 feature descriptions........................43 menu #1 - basic features.................43 menu #2 - advanced features ..............44 menu #3 - remote start options.............46 nuisance prevention circuitry™................48 valet mode .............................. 48 timer mode.............................. 49 table of zones............................49 shutdown diagnostics......................50 to perform shutdown diagnostics............50 long term event history ..................... 50 safety check.............................51 troubleshooting..........................52 alarm troubleshooting...................52 remote start troubleshooting...............53 wiring quick reference guide..................55 relay satellite wiring quick reference guide........56 3 warning! safety first The following safety warnings must be observed at all times: ■ Due to the complexity of this system, installation of this product must only be performed by an authorized Ungo dealer. ■ When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Ungo dealers should make the following recommendations to all users of this system: 1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). 2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. 3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle. 4. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. ■ Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotel...