Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Sony Dateigröße: 2.45 mb Dateiname: CECH-2501B-3.30_1.pdf Unterrichtssprache:

Notice When you perform this operation, all of the data that is stored on the PS3™ system that will receive the data (the destination system) will be deleted. For details on how to use the utility and its limitations, refer to the online user’s guide (Restoring the PS3™ system Notices . If you restore the default settings or restore the PS3™ system, changes to the settings cannot be undone. Data loss or corruption is the responsibility of the user. . Do not turn off the PS3™ system during this operation. If the operation is cancelled before completion, the system software may become damaged, and the system may require servicing or exchange. . During this operation, the power button on the system and the PS button on the wireless controller are not active. . You cannot use this feature to go back to an earlier version of the system software. You can restore from the current settings under (Settings) to the default settings by selecting (Settings) (System Settings) [Restore Default Settings]. After you complete the operation and restart the system, the initial setup screen will be displayed. Follow the on-screen instructions to perform initial setup of the system software ( page 15). Deleting data on the hard disk drive You can delete all data on the system’s hard disk and restore from the current settings under (Settings) to the default settings by selecting (Settings) (System Settings) [Restore PS3™ System]. You can shorten the time required to perform this operation by selecting [Quick Format] from the list of hard disk format options. It is recommended that you select [Full Format] when formatting a hard disk that contains important or sensitive data. After you complete the operation and restart the system, the initial setup screen will be displayed. Follow the on-screen instructions to perform initial setup of the system software ( page 15). Before disposing of or transferring the PS3™ system Before disposing of the system, it is recommended that personal information and other data of similar nature be deleted. To delete data, go to (Settings) (System Settings) [Restore PS3™ System]. It is recommended that you select [Full Format] when the screen for selecting a hard disk format method is displayed during system restoration. Although formatting time can be reduced by using [Quick Format], it might be possible to restore erased data in some cases if a special tool is used. Before requesting service Go through this section if you experience difficulty in operating the PS3™ system. Should any problem persist, contact Consumer Services ( back cover) for assistance. Power The system does not turn on. . Check that the AC power cord is securely inserted in the system and the electrical outlet. When the power button is pressed, the system beeps repeatedly and then the power indicator will turn off. . The temperature inside the system is becoming too high. Check whether the system is being used in a location that is too warm. Ensure that vents are not blocked and that there is adequate airflow around the system. Press the power button. (The power indicator will become solid red.) Wait a while, and then turn on the system again. Picture There is no picture on the TV screen. . Check that the cable is securely inserted. Try disconnecting the cable from the PS3™ system or TV and then reconnecting it. . There may be a problem with the AV cable in use. Try using another cable that is compatible with the PS3™ system. . Adjust the video input on the TV to match the input connector that is being used to connect to the PS3™ system. . If the video output settings on the system do not match those of the cable or TV in use, there may be no picture. If the screen goes blank, turn off the system. Then, with only the system and the TV connected, press the system’s power button for more than 5 seconds to turn the system back on. The video output settings will automatically be reset to the standard definition (SD) resolution. US Before requesting The picture is distorted. . Check that the cable is securely inserted. Try disconnecting the cable from the PS3™ system or TV and then reconnecting it. The Blu-ray Disc (BD) or DVD cannot be played, or the picture is distorted. . When outputting DVD content or PlayStation®3 format software in standard definition (SD) resolution, only discs recorded in the NTSC standard can be played. . If the system is connected to a VCR, copy protection encoding on some BDs and DVDs may cause image distortion, or may cause the image to become lighter or darker. In such cases, connect the system to the TV directly. You may also see a similar occurrence if using a combination TV/VCR unit. . If the BD or DVD does not match the region code set in the system, it cannot be played. For details, see "Region codes" ( page 50). . Some DVDs are preset with parental control restrictions. Enter the password that was set in (Security Settings) to temporarily increase the pare...

Herunterladen

Geben Sie zwei Ziffern: