Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Audio output: can be selected from approx. 1-30 sec. Picture to be displayed: changes with the timing you set on the time lapse VCR. Audio output: changes at the time set on the time lapse VCR. SEQ/VCR Picture to be displayed: can be selected from approx. 1-30 sec. Audio output: changes at the same time as the picture. Picture to be displayed: changes at the time set on the time lapse VCR. Audio output: changes at the time set on the time lapse VCR. 3. Timing Selection (TIMING SELECT) 5. Page Sequence (PAGE SEQ) ** SET UP MENU ** CAMERA ID 1.34..7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT .T^LAPSE] PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12 . . 5. . 8 END SET UP ENABLE ** SET UP MENU ** CAMERA ID 1.34..7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT T-LAPSE PAGE SEQ f2SEC] ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12..5..8 END SET UP ENABLE 3-1. Move the cursor to “TIMING SELECT." 3-2. Select “REAL TIME" (real timing) or ‘T-LAPSE" (time lapse timing) using the Left (-<) or Right Switch (►). Note: Set this item to “T-LAPSE" when the timing signal is input from the time lapse VCR. When the timing pulse from the time lapse VCR has not been supplied for a short time, REAL TIME is automatically selected. 4. Sequential Time Adjustment (SEQ TIME ADJ) -;-:-\ ** SET UP MENU ** CAMERA ID 1.34..7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT T-LAPSE -------- PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12..5..8 END SET UP ENABLE V___/ f N ** SET UP MENU ** CAMERA ID 1.34..7. 1 CAMERA.. AUDIO SELECT SEQ TIMING SELECT REAL TIME 4 SEQ TIME ADJ 1SEC PAGE SEQ ---- ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12..5..8 END SET UP ENABLE V In case of T-LAPSE is selected for TIMING SELECT, sequential time synchronizes with the switching signal of the time lapse VCR. You cannot set by this monitor. In case of REAL TIME is selected for TIMING SELECT, you can select one of the two sequential time adjustments by MONITOR MODE switch; 1. When QUAD/SPOT is selected for MONITOR MODE, the sequential time is automatically set to the switching frame by frame. 2. When SEQA/CR is selected for MONITOR MODE, you can select the sequential time from approx. 1-30 seconds. (The recording output to VCR is switched frame by frame.) Also sequential time of SEQ for AUDIO SELECT is set’in this menu (1-30 sec.). 4-1. Move the cursor to “SEQ TIME ADJ." 4-2. Select sequential time using the Left (M) or Right switch (►). Sequential time can be selected from approx. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, or 30 seconds. 5-1. Set MONITOR MODE to QUAD/SPOT. 5-2. Move the cursor to “PAGE SEQ." 5-3. Select the sequential time of the quad page using the Left (•*) or Right switch (►). The switch timing of sequential pages can be selected from approx. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, or 30 seconds. 6. Alarm Recording Mode Setting (ALARM REC MODE) r N ** SET UP MENU ** CAMERA ID H * 1 CAMERA AUDIO SELECT 1 TIMING SELECT T-LAPSE SEQ TIME ADJ -------- PAGE SEQ 2 SEC ALARM REC MODE [FRAME] ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12..5..8 END SET UP ENABLE V > 6-1. Move the cursor to “ALARM REC MODE." fi-2. Select alarm recording mode from FRAME or SPOT using the Left (*<) or Right switch (►). 7. Alarm Time Adjustment (ALARM TIME ADJ) /-\ ** SET UP MENU ** CAMERA ID 1.34..7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT T-LAPSE SEQ TIME ADJ ------ PAGE SEQ 2SEC ALARM REC MODE FRAME_ . ALARM TIME ADJ [10SEC_BZ]^ I AUTO RESET OFF BRIGHT COMP 12..S..8 END SET UP ENABLE V___ 7-1. Move the cursor to “ALARM TIME ADJ." 7-2. Adjust the alarm time to 1, 5, 10, 20, 30, 40, 50, or 60 seconds using the Left (-