Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The serial number of this product may be found on the left of the unit. You should note the senal number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. _ Serial No.-- WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. ■ Preface The WJ-SX850 is a card cage designed to allow flexible system expansion of the System 850 Matrix Switcher. It is provided with a power supply for the boards installed, and a Local CPU board to control boards in the cage. ■ Appearance • Front View • RearView G) Operate Indicator (OPERATE) Is on when the power of the WJ-SX850 Matrix Switcher Card Cage is turned on. Note: The power switch of this cage is located underneath the front panel. Remove the front panel by removing two screws on the panel. CD VS/VD Input Connector (VS/VD IN) Accepts either the VD (Vertical Drive) pulse or the VS {Video Sync) signal for synchronizing the system. Notes: • This input is looped through to the VS/VD Output Connector. • When the VD (or VS) signal is supplied to the VS/VD Input Connector, turn the VS/VD selection switch (SW7) on the circuit board to the VD (or VS) position. The factory default setting of the VS/VD selection switch (SW7) is VD. Ask qualified service personnel about setting up this switch. • The external sync signal should meet EIA RS-170 specifications and should not contain any jitters, such as a VCR playback signal. -2- (D VS/VD Output Connector (VS/VD OUT) Outputs either the VD (Vertical Drive) pulse or the VS (Video Sync) signal for synchronizing other system components. Note: The input at the VS/VD Input Connector is looped through to this output. These inputs and outputs are connected internally. 0 VD Output Connector (VD OUT) Outputs VD (Vertical Drive) pulses for synchronizing other system components. Notes: • The internal VD pulse or the looped-through external VD pulse is provided at this connector. • When the VS signal is supplied to the VS/VD Input Connector, the VD output signal from the VD Output Connector will be delayed by approximately 15 ps with respect to the V-sync of the VS input signal. 3H v VS input signal VD output signal t--1 r approx. I5pisec (D Ethernet Port (ETHERNET) For exchanging control data with the Central Processing Unit (CPU) via Ethernet. © RS-232C Port (RS-232C) This port is used only for factory tests. (D AC Inlet Socket (AC IN) Plug the power cord (supplied as a standard accessory) into this socket and connect the cord to an AC outlet. ■ Board Setting The following settings should be made by qualified service personnel or system installers. 1. Remove the front panel by removing two screws on 2. Extract the Local CPU board by raising up the card the panel. puller. — Caution - Hold this board only by its edges. Otherwise components on the board may be damaged by static electricity. SW1: Factory use only SW3: LCPU Reset Switch SW2: Cord Cage Reset Switch 3. Set switches (SW9, SW10 and SW12) on the board to designate the cage number as shown below. The cage number and corresponding switch settings are given in the following address table. The factory default setting is 000. Cage No. SW Setting Cage No. SW Setting SW12 SW10 SW9 SW12 SW10 SW9 1 0 0 1 16 0 1 1 2 0 0 2 17 0 1 2 3 0 0 3 18 0 1 3 4 0 0 4 19 0 1 4 5 0 0 5 20 0 1 5 6 0 0 6 21 0 1 6 7 0 0 7 22 0 1 7 8 0 0 8 23 0 1 8 9 0 0 9 24 0 1 9 10 0 0 A 25 0 1 A 11 0 0 B 26 0 1 B 12 0 0 C 27 0 1 C 13 0 0 D 28 0 1 D 14 0 0 E 29 0 1 E 15 0 0 F 30 0 1 F 241 1 0 1 256 1 1 1 242 1 0 2 257 1 1 2- 243 1 0 3 258 1 1 3 244 1 0 4 259 1 1 4 245 1 0 5 260 1 1 5 246 1 0 6 261 1 1 6 247 1 0 7 262 1 1 7 248 1 0 8 263 1 8 249 1 0 9 264 1 1 9 250 1 0 A 265 1 1 A 251 1 0 B 266 1 1 B 252 1 0 C 267 1 1 C 253 1 0 D 268 1 1 D 254 1 0 E 269 1 1 E 255 1 0 F 270 1 1 F Designate further cage numbers, referring to the above address table. Cage numbers are available up to 1 024. 4. Set switch (SW7) on the board to select either VD or VS for the Sync input signal, if applicable. The factory default setting is VD. SW7 5. Confirm that switch (SW11) on the board is set to E2P position. TJ~ SW11 [E2P| [SH^Fl VD] [VS 6. Confirm that switches (SW4, SW8 and SW13) on the board are set as follows: 7. Place the board into the CPU slot in the front of the cage by sliding it along the board guide. ON BBBB 12 3 4 Switch Number Setting Positions 1 2 3 4 SW4 ON OFF ON OFF SW8 ON ON ON ON SW13 OFF OFF OFF OFF DIP SW8 OFF ON 1 PROM Mode Normal Mode 4 MAC Address Write-enable Mode Normal Mode ■ Specifications Power Supply: Power Consumption: VS/VD Input/Output: VD Output: Ethernet Port: RS-232C Port: Ambient Operating Temperat...