Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: EverFocus Dateigröße: 1.93 mb Dateiname: Unterrichtssprache:

SELECT: Press this key to select, to assign a camera to a display, to adjust screen display, and so on. CALL: Press this key to enter and set up CALL MENU. DISPLAY: Press this key to switch display of channels and/or status bar. 16 17 18 MENU: Press this key to enter or quit MAIN SETUP MENU. HDD LOCK: Protect HDD without steal and turn on HDD power. Hard Disk Tray: Hard Disk holder for HDD. 12 19 19 20 21 22 23 Shuttle and Jog Dial Shuttle: In the Playback mode, turn the Shuttle dial to fast forward/rewind the video. In the Pause mode, turn the Shuttle dial to slow forward/rewind the video. In the Search mode, turn the Shuttle to change pages. Jog Dial: In the Pause mode, turn the Jog dial to forward/rewind the video. In the Menu mode, turn the Jog dial to change settings and values in subentries. USB Slot: Insert a USB to archive an image or video file. HDD LEDs: LEDs for HDD active power (GREEN) and data reading /writing (YELLOW). Remote Control: IR remote control receiver. System LEDs: LEDs for system active LAN, ALARM and POWER display. 13 1.4 BACK PANEL CONNECTORS Back panel of 810H Back panel of 810M Back panel of 410M Back panel of 410H POWER Main Power plug: Connect the DC 12~ 24V power source to adapter for AC 100~ 240V. 1 14 AUDIO 2 AUDIO 2 Audio IN: Audio input for recording, and it can be set to “YES”or “NO” in the RECORD SETUP MENU. Audio OUT: Connect to an audio input of a monitor or other device. MONITOR 3 MAIN MONITOR: This connector is used for the main monitor display, a number of different display modes may be selected for viewing. 4 CALL MONITOR: This connector is used for the call monitor. This monitor can only display a full screen or a quad screen. VIDEO IN 5 For EDR810 Series: VIDEO IN(1~8): The BNC connectors of video input enables the system to receive the signals from each camera through the 75 ohm coaxial cables. Alarm Input/Output Alarm Input 6 ALM-INPUT: Normal open or normal close type alarm signal inputs. The Alarm Input can be selected as Normal Open (N.O.), Normal Close (N.C.), N.C. TRANS., or N.O, TRANS input in the ALARM SETUP MENU. When an alarm occurs, alarm recording will automatically start. ALM-OUTPUT: A build-in relay offers 3 nodes which are ALM-COM (common), ALM-NO (normal open) and ALM-NC (normal close) for external use. Note: Please check APPENDIX C to see other available alarm input/output functions. 15 RS232 8 RS485 9 8 RS485 9 LAN LAN Connector: The RJ-45 LAN connector. 7 RS232 connector: Connect D-Sub 9 pins connector to RS232 ports for remote control. RS485 connector: RJ 45 Connector to Cascade multi Digital Video Recorder. Remote 10 Remote Control: Remote control port provides you an extension wire with an IR receiver instead of the IR receiver on the front panel. Note: The IR receiver extension line (10m) must be purchased separately. Wireless LAN (Reserved) 11 Antenna: Integrated IEEE 802.11b/g wireless LAN capabilities. The antenna port is for wireless network antenna use (For EDR810M option). 12 FAN: Cooling FAN. 16 3 4 Select sign: You can assign a camera to a display by pressing SELECT key in life mode. Dial Jog to move the select sign to the display you would like to change camera, and then press FULL + channel key to relocate the camera. Play status bar: The play status bar appears in play back mode if you enable a status bar on the screen (Check page 12, item 15th, DISPLAY). Three parts which are play date, play time and play status are shown in the play status bar. Play Date Play Status Play Time 5 1. Play date: The play date in which the video is recorded. 2. Play status: It shows PAUSE, play speed and reverse play speed. “PAUSE”, when the video play is paused. “>” means normal play speed; “<“ means normal reverse play speed; “>> x N” means N time fast play speed; “<< x N” means N time fast reverse play speed. 3. Play time: The play time at which the video is recorded. The time format depends on the time format setting in the TIME/DATE SETUP MENU. Record status bar: The record status bar appears when you enable a status bar on the screen (Check page 12, item 15th, DISPLAY). Three parts which are current date, record status (% of space used for recording) and current time. Current Date Record Status Event Current Time HDD/FAN Status 18 1. Current date: The current date which is set in the TIME/DATE SETUP MENU. 2. Record status: It shows REC and recording hard disk number. “REC”, it shows when machine is recording. “R01”, the recording hard disk number. There is only one hard disk available in this model, so it always shows R01 when recording. 3. Event: The last happened event. 4. Current time: The current time which is set in the TIME/DATE SETUP MENU. 5. HDD/Fan status: “No Disk”, it shows when no disk is installed or detected. “No Fan”, it shows when cooling fan stops working. 19 2. INSTALLATION The installations described below should be done by qualified service personnel or system installers. 2.1 PACKING LIST Please check accessories in the p...

Herunterladen

Geben Sie zwei Ziffern: