Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Enerco Dateigröße: 1000.98 kb Dateiname: Unterrichtssprache:

• Equipment shutoff valve* • Ground joint union 5 Installation instructions and Owner’s Manual 36” min. from ceiling 6” Min from adjoining walls Left Side Right Side Floor 2” min. to top surface of carpet, tile or other combustible material Figure 4 FASTENING HEATER TO WALL Mounting Bracket The mounting bracket in located on the back panel of heater (see figure 5). It has been taped there for shipping. Remove mounting bracket from back panel. Figure 5 Mounting Bracket Removing Front Panel of Heater 1. Remove three screws on bottom front of front panel. 2. Pull bottom of front panel forward, then down (see figure 6) Figure 6 Attaching Mounting Bracket to Wall Use holes on each end of mounting bracket to attach bracket to wall. These holes are 16 inches apart. Attach mounting bracket to wall in one of two following ways. 1. Attach to wall studs 2. Attach to wall anchor Attaching to Wall Stud: This way is the best providing the strongest mounting in wood frame houses. Attaching to Wall Anchor: This way allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry). Decide which way best suits your needs. Either method will provide a secure hold for the mounting bracket. 1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level. For wall stud mounting locate one end of the mounting bracket over a wall stud. WARNING: Maintain minimum clearances shown in figure 8. If you can, provide greater clearances from the floor and joining wall. 2. Mark screw locations on wall (see figure 7). 3. Remove tape and mount bracket from wall. 17-1/2” Min. Adjoining Wall 6-1/2” Min. 10,000 BTU 10-1/4” min 20,000-30,000 BTU 16” (Lg) 12-9/64” (Sm) Mark mounting hole locations and drill holes where indicated. Allow for minimum clearances 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012 Figure 7 Attaching to Wall Stud: For attaching mounting bracket to wall studs 1. Drill holes at marked locations using 9/64” drill bit. 2. Place mounting bracket onto wall. Line up holes on each end of bracket with hole drilled in wall. 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching to Wall using Anchor: For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater. Installation instructions and Owner’s Manual 70574 REV. C 8/05 6 1. Drill holes at marked locations using 5/16” drill bit. For solid walls (concrete or masonry), drill at least 1” deep. 2. Fold wall anchor as shown in figure 8 below. Figure 8. 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2” or less) insert red key into wall anchor. 5. Place mounting bracket onto wall. Line up holes on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is firmly fastened to wall. Placing Heater on Mounting Bracket 1. Locate two horizontal slots on back pane of heater (see figure 9). 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Horizontal Slots Mounting Bracket mounted to wall Figure 9. Installing Bottom Mounting Screws 1. Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see figure 10). Figure 10 2. Mark screws locations on wall. 3. Remove heater from mounting bracket. 4. If installing bottom mounting screw into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching to Wall using Anchor. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64” drill bit. 5. Re-place heater onto mounting bracket. 6. Place spacers between bottom mounting holes and wall anchor or drilled hole. 7. Hold spacer in place with one hand. With the other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole. 8. Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not re-place front panel at this time. Replace front panel after making gas connections and checking for leaks. FLOOR MOUNTING AWAY FROM WALL: Figure 11 Installing Support Feet (see figure 11) 1. Lay heater onto table on its back with bottom edge overhanging table edge. 2. Securely attach feet to bottom of heater using 2 – self-tapping screws each. Note: Feet should have long end going out the front of heater, and the edge coinciding with side of heater. If feet overhang side of the heater, switch leg location. 3. Place heater on non-combustible surface (see Locating Heater above) before proceedi...

Herunterladen

Geben Sie zwei Ziffern: