Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Desa Dateigröße: 262.07 kb Dateiname: 598-1158-01.pdf Unterrichtssprache:

120 VAC, 60 Hz Operating Modes . . . . TEST, AUTO, and MANUAL MODE Time Delay . . . . . . . . 1, 5, 10 minutes Range . . . . . . . . . . . . Adjustable DESA Specialty Products™ reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold. . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (2.5 cm) away from the lamps. . Adjust the RANGE as needed. RANGE set too high may increase false triggering. . Secure the sensor head by tightening the clamp screw. Do not overtighten the screw. Clamp Screw Ball Joint Aim Sensor Down for Short Coverage Aim Sensor Higher for Long Coverage . Set the amount of TIME you want the lights to stay on after motion is detected (1, 5, or 10 minutes). 598-1158-01 3 TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE Lights will not come on. 1. Light switch is turned off. 2. F l o o d l i g h t i s l o o s e o r burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Daylight turn-off is in effect (recheck after dark). 5. Incorrect circuit wiring, if this is a new installation. 6. Re-aim the sensor to cover desired area. Lights come on in daylight. 1. Light Control may be installed in a relatively dark location. 2. Light Control is in Test. (Set control switch to an ON-TIME position). Lights come on for no apparent reason. 1. Light Control may be sensing small animals or automobile traffic (re-aim sensor). 2. R a n g e i s s e t t o o h i g h . (Reduce Range). SYMPTOM POSSIBLE CAUSE Lights stay on 1. A flood lamp is positioned too close to continuously. the sensor or pointed at nearby objects that cause heat to trigger the sensor. (Reposition the lamp away from the sensor or nearby objects). 2. Light Control is pointed toward a heat source like an air vent, dryer vent, or brightly-painted heat-reflective surface. (Reposition sensor). 3. Light Control is in Manual Mode. (Switch to Auto.) Lights flash on 1. Heat or light from the lamps may be and off. turning the Light Control on and off. (Reposition the lamps away from the sensor). 2. Heat being reflected from other objects may be affecting the sensor. (Reposition sensor). 3. Light Control is in the Test mode and warming up.(Flashing is normal under these conditions). 4. Light may be leaking through the floodlamp reflectors. (Make sure the metal lamp protectors are installed.) TECHNICAL SERVICE Please call 1-800-858-8501 for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F).You may also write* to: DESA Specialty Products™ P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service Specialty Products * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product TEN YEAR LIMITED WARRANTYThis is a “Limited Warranty”which gives you specific legal rights.You may also have other rights which vary from state to state or province to province. For a period of ten years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Not Covered -Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty.Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety.This warranty does not include reimbursement for incon- venience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty covers only DESA Specialty Products™assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMERANDTHERESHALLBENOLIABILITYONTHEPARTOFDESASPECIALTYProducts™FORANYSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGES,INCLUDINGBUTNOTLIMITEDTOANYLOSSOFBUSINESSORPROFITS,WHETHERORNOTFORE- SEEABLE.Somestatesorprovincesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sotheabovelimitationorexclusionmaynotapplytoyou.Proofofpurchaseisrequiredforwarrantyclaims. 4 598-1158...

Herunterladen

Geben Sie zwei Ziffern: