Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Sony Dateigröße: 1021.64 kb Dateiname: Unterrichtssprache:

When it ends, press X PAUSE again to resume recording. Note • If you start recording following the procedure above, the VCR will not start recording with the APC function. To record a tape with the APC function, press z REC again during recording pause in step 3 so that the VCR analyses the tape. Then when you start recording in step 4, press X PAUSE after the APC indicator stops flashing. If you press X PAUSE before the APC indicator stops flashing, the APC function is cancelled. Editing Audio dubbing (SLV-EZ77AS/ EZ77NZ only) This feature lets you record over the normal audio track. The monaural sound previously recorded is replaced while the original hi-fi sound remains unchanged. Use this feature to add commentary to a tape that you have recorded with a camcorder. Before you start editing • Turn on your TV and set it to the video channel. • Press INPUT SELECT or PROG +/– to display “L1”, “L2” or “L3” in the display window. 1 Insert a source tape into the stereo system (or the playback VCR). Search for the point to start playback and set it to playback pause. 2 Insert a prerecorded tape into this (recording) VCR. Search for the end of the section to be replaced and press X PAUSE. Make sure that the tape has its safety tab in place. 3 Press CLEAR to reset the counter to “0:00:00.” 4 Rewind the prerecorded tape to the beginning of the section to be replaced. The VCR pauses. 5 Press AUDIO DUB. The indicator appears in the display window. 6 To start editing, press the X PAUSE buttons on this VCR and the stereo system (or other VCR) at the same time. When the counter reaches “0:00:00”, audio dubbing stops automatically. To stop while editing Press the x STOP buttons on this VCR and the stereo system (or other VCR). To listen to both the hi-fi and normal audio Set AUDIO MIX to ON in the SET UP MENU (page 61). Use this feature to listen to dubbed audio over the original hi-fi audio. When AUDIO MIX is set to ON, the AUDIO MONITOR button does not function. Remember to reset AUDIO MIX to OFF after playing the tape. CLEAR AUDIO DUB X PAUSE 1 2 3 Editing Additional Information Troubleshooting If you have any questions or problems not covered below, please consult your nearest Sony service facility. Symptom Remedy Playback Clock Power The ?/1 ON/STANDBY switch• Connect the mains lead to the mains securely. does not function. The power is turned on but the • Moisture condensation has occured. Turn the power VCR does not operate. off, unplug the mains lead and leave the VCR to dry for over four hours. The clock has stopped and • The clock stops if the VCR is disconnected from the “–:– –” lights in the display mains for more than eight hours. Reset the clock (and window. timer). The playback picture does not • Make sure the TV is set to the video channel. If you are appear on the TV screen. using a monitor, set it to video input. • If you made connections using the aerial cable only, make sure the RF channel number is set correctly for your area. The picture or sound is • Adjust the tracking with the TRACKING +/– buttons. distorted. • Make sure the colour system is correctly set to the system that the tape was recorded in. The picture is not clear, or a message appears indicating that the video heads need cleaning. • The video heads are dirty (see page 67). Clean the video heads using the Sony T-25CLD, T-25CLW or E-25CLDR video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required). Do not use a commercially available liquid type cleaning cassette other than Sony’s, as they may damage the video heads. • If a message appears, this indicates that the Head Condition Sensor has detected dirty video heads. Follow the on-screen message. For details about the Head Condition Sensor, see page 68. • The video heads may have to be replaced. Consult your local Sony service facility for more information. The picture rolls vertically during picture search. • Adjust the vertical hold control on the TV or monitor. The picture has no sound. • The tape is defective. • If you made A/V connections, check the audio cable connection. The sound is unstable or has an echo. • When you play a tape with the same sound recorded on both the hi-fi and normal sound tracks, make sure the AUDIO MIX option in the SET UP MENU is set to OFF. continued Additional Information Troubleshooting (continued) Symptom Remedy Synchronised Recording Timer recording Recording No TV programmes appear on the TV screen. • Make sure the TV is set to the video channel. If you are using a monitor, set it to video input. • Select the correct source with the INPUT SELECT or PROG +/– buttons. Select a programme position when recording TV programmes; select “L1” or “L2” (or “L3”: SLV-EZ77AS/EZ77NZ only) when recording from other equipment. TV reception is poor. • Adjust the TV aerial. The tape starts playing as soon as it is inserted. • The saf...

Herunterladen

Geben Sie zwei Ziffern: