Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Recording of video sources based on other colour systems cannot be guaranteed. Introduction Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 9 Step 3: Connecting the VCR 11 Step 4: Tuning your TV to the VCR 13 Step 5: Setting up the VCR with the Auto Set Up function 15 Step 6: Setting the clock 19 Manual setup — Selecting a language, Presetting channels, Setting up ShowView* 27 Setting the Canal Plus decoder Getting Basic Operations 31 Playing a tape 34 Recording TV programmes 38 Recording TV programmes using ShowView 42 Setting the timer manually Additional Operations 45 Playing/searching at various speeds 48 Recording TV programmes using the quick timer 49 Checking/changing/cancelling timer settings 51 Searching using the index function 52 Adjusting the picture 54 Changing menu options Editing 56 Connecting to a VCR 59 Basic editing 60 Audio dubbing Additional Information 61 Troubleshooting 64 Specifications 65 Index to parts and controls Back cover Index * ShowView is a trademark applied for by Gemstar Development Corp. ShowView system is manufactured under license from Gemstar Development Corporation. Introduction 3 Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • Aerial cable • R6 (size AA) batteries Getting Started Step 2 Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Using the remote commander You can use this remote Remote sensor commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. To operate the VCR Set TV / VIDEO to VIDEO and point at the remote sensor on the VCR TVE/ VIDEO 1 2 3 4 5 6 7 8 9 0 a Sony TV TV and point at the remote sensor on the TV Getting continued Getting Started 5 Step 2 : Setting up the remote commander (continued) MENU WIDE AUDIO MONITOR FASTEXT buttons TV/VIDEO DISPLAY ; V TV control buttons 1 2 3 4 5 6 7 8 9 0 ON/STANDBY OK CURSOR >/./?// Programme number buttons PROG+/–/ A/. VOL+/– To Press Turn the TV into standby or active mode ON/STANDBY Select an input source of the TV either from aerial in or from line in TV/VIDEO Select the programme position of the TV Programme number buttons PROG +/– Adjust the volume of the TV VOL +/– Switch to TV (Teletext off) ;(TV) Switch to Teletext V (Teletext) Getting Started To Press Select the sound AUDIO MONITOR Use FASTEXT FASTEXT buttons Call up on-screen display DISPLAY Change the Teletext page A/. Operate TV menu options MENU CURSOR >/./?// OK Switch to/from wide mode of a Sony wide TV (For WIDE other manufacture’s wide TV, see “Controlling other TVs with the remote commander” below.) Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one together. • Do not use different types of batteries together. Controlling other TVs with the remote commander The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the table below, set the appropriate manufacturer’s code number. 1 Set TV / VIDEO at the top of the remote commander to TV . 2 Hold down ON/STANDBY, and enter your TV’s code number(s) using the programme number buttons. Then release ON/STANDBY. Now you can use the following TV control buttons to control your TV: ON/STANDBY, TV/VIDEO, programme number buttons, ?(ten’s digit), PROG +/–, VOL +/–, ;(TV), V (Teletext), FASTEXT buttons, WIDE*, MENU*, CURSOR >/./?//*, and OK*. * These buttons may not work with all TVs. Tip • When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically. continued Getting Getting Started 7 Step 2 : Setting up the remote commander (continued) Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. To make wide mode settings, see the footnotes below this table for the applicable code numbers. Manufacturer Code number Manufacturer Code number Sony 01*1, 02, 03, 04, 05 NEC 66 Aiwa 32 Nokia 15, 16, 69*3 Akai 68 Nordmende 35, 42 Blaupunkt 10, 21 Orion 47, 48 Brionvega 40 Panasonic 17*1, 49 C.G.M 09 Philips 06*1, 07*1, 08*1 Colonad 03 Phonola 18, 19 Dual 44 Pioneer 26 Emerson 03, 04 Saba 12, 13 Fenner 30, 31 Samsung 22, 23 Ferguson 52 Sanyo 25 Gold Star 03, 04, 17 Schneider 46 Grundig 10*1, 11*1 Seleco 14 Hitachi 24 Sharp 29 Hyper 31 Siemens 39 Inno-Hit 41 Sinudyne 37 Irradio 20 TEAC 67 ITT 15, 16, 69*3 Telefunken 36 JVC 33*1 Thomson 43*2 Loewe 45 Toshiba 38 Mitsubishi 27*1, 28*1, 50*1, 51*1 White Westinghouse 34 Mivar...