Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Features for a Quality Picture Digital Auto Picture Automatically controls the video output signal for less noise depending on the tape condition. Digital Auto Tracking Continuously analyzes the signal and adjusts for optimum picture quality. Manual Tracking Control (to reduce picture noise) Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on the VCR until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later. • Important Accessories Prevent Tape • Specifications Prevent Accidental Tape Erasure Tape Speed Setting Type of Video Cassette T120 T160 T180 SP (Standard Play) 2 Hours 2 Hours 40 Minutes 3 Hours SLP (Super Long Play) 6 Hours 8 Hours 9 Hours R R R R R V-Lock Control (to reduce picture jitter) In Still mode, CH (TRACKING) / operate as a V-Lock control. - 3 Connections / Initial Setup (Ready to Play) Connections / Initial Setup (Ready to Play) Make all cable or antenna connections before plugging into an AC outlet. Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set. Connecting (Select a method) For ANT./Cable . ..... VCR . ..... TV 1 Connect cable from Antenna/Cable to VCR’s IN FROM ANT. jack. 2 Connect VCR’s OUT TO TV jack to TV’s ANT. IN jack with included RF Cable. For DSS/Cable Box . ..... VCR . ..... TV 1 Connect your cable box’s OUT jack to the VCR’s IN FROM ANT. jack with an RF cable. 2 Connect VCR’s OUT TO TV jack to TV’s ANT. IN jack with included RF Cable. Initial Setup (Ready to Play) 1 Turn TV on and tune to channel 3. 2 Plug VCR Power Cord into AC wall outlet. VCR comes on and auto channel and clock set starts. • If screen below does not appear... check all connections. Try tuning TV to channel 4. • To change VCR’s output channel, see “VCR’s Output Channel” (p. 12) in Advanced Operations book. 1 2 2 1 Over tightening “Nut type” RF coaxial cables may damage jacks. Finger tighten only. 3 Settings are made automatically. When complete, this screen appears. If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock (below). Plug VCR Power plug into an AC wall outlet. AUTO CLOCK SET PROCEEDING CANCEL : STOP CH AUTO SET PROCEEDING CANCEL : STOP If you use a cable box, turn it on and set it to the Public Broadcasting Station (PBS) channel in your time zone. If you use a DSS receiver, it must be turned off. Notes • Function buttons are void during Initial Setup. • To eject a tape during Auto Set, press EJECT on remote or STOP twice on VCR. Then make settings manually. (See Advanced Operations book, p. 12.) • If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See Advanced Operations book, p. 12.) AUTO CLOCK SET IS INCOMPLETE PLEASE SET CLOCK BY PRESSING ACT ION KEY Manual Clock Set If Auto Clock Set was incomplete. 1 Press ACTION* on remote to display CLOCK menu. 2 Press to select the month and to set. In the same manner, select and set the date, year, time, and DST (Daylight Saving Time). 3 Press ACTION to start clock and exit. - 4 Playback / Record on a Tape • Connections Initial Select • Record • Auto Playback / Record on a Tape • Connections Initial Select • Record • Auto Playback a Tape 1 Insert a tape. • Loose or peeling labels may cause tape jam. • VCR power comes on. If Auto VCR/TV (see p. 10 of Advanced Operations book) is set to “OFF,” press VCR/TV. 2 Press PLAY to play tape. • If tape has no rec. tab (p. 3), auto play begins. Special Features During Play Forward/Reverse Scene Search . Press FF or REW. . Press PLAY to release. After search has begun, each additional press of FF or REW changes speed as shown below. [SP] : Approx. 9X - Approx. 13X [SLP] : Approx. 27X - Approx. 43X Notes • Picture interruption may occur with some TVs. • FF and REW search speed may vary depending on current tape position. • After 10 minutes in search mode, VCR returns to Play mode to protect the tape and the video heads. Still (Freeze) Picture . Press PAUSE/SLOW. . Press PLAY to release. Slow Motion Picture . Hold down PAUSE/SLOW in Still mode. . Press PLAY to release. Notes • These features work best in SP or SLP mode. • The sound will be muted. • To reduce picture noise, see “Manual Tracking Control” on p. 3. • After 3 minutes in Still or Slow mode, VCR stops to protect the tape and the video heads. 3 Press STOP to stop tape. Rapid Rewind/FF Press REW or FF in Stop mode to rewind or fast forward tape. • Rewinds a T-120 tape in approx. 1 minute. Press EJECT on remote, or STOP/EJECT on VCR to eject tape. Auto Operation Functions Auto Play Record on a Tape 1 Insert a tape with a record tab (p. 3). • VCR power comes on. If Auto VCR/TV (see p. 10 of Advanced Operations book) is set to “OFF,” press VCR/TV. 2 Press CH or NUMBER keys to select the channel. • If channel number is over 100, first press 100 key then the other 2 digits. • For “LINE” input, see p. 9 of “Advanced Operations” book. 3 Press SPEED to set record speed (p. 3)...