Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Remaining recording time When there is no more free space on the memory, “ End” (built-in memory) or “ End” (memory card) will be displayed and the recording will stop. 24F progressive frame rate Select the 24F progressive frame rate ( Memory operation Record, Record pause, Playback, Playback pause, Fast playback, Fast reverse playback, Slow playback, Slow reverse playback, Frame advance, Frame reverse. Remaining battery time • The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately. • The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery pack. The remaining recording/playback time of the battery pack is displayed, in minutes, next to the icon. • When is displayed in red, replace the battery pack with a fully charged one. • When you attach an empty battery pack, the power may turn off without displaying . • Depending on the conditions under which the camcorder and the battery pack are used, the actual battery charge may not be indicated accurately. • When the camcorder is off, press to display the charge status of a battery pack. The Intelligent System will display the charge status (as a percentage) and the remaining recording time (in minutes) for 5 seconds. If the battery pack is exhausted, the battery information may not be displayed. Remaining recording time When there is no more free space on the memory, “ End” (built-in memory) or “ End” (memory card) will be displayed and the recording will stop. 24F progressive frame rate Select the 24F progressive frame rate ( 66) to give your recordings a cinematic look. You can combine this frame rate with the [ Cine Mode] recording program to enhance the effect. Number of available photos in red: There is no memory card in the camcorder. in green: 6 or more photos in yellow: 1 to 5 photos in red: No more photos can be recorded. • When viewing the photos, the display will always be in green. • Depending on the recording conditions, the number of available photos displayed may not decrease even after a recording has been made, or may decrease by 2 photos at once. 100% 75% 50% 25% 0% BATT.INFO 26 • Introduction terminal DC IN Preparations This chapter describes basic operations, such as navigating the menus, and first time settings to help you learn more about your camcorder. Getting Started Charging the Battery Pack The camcorder can be powered with a battery pack or directly using the compact power adapter. Charge the battery pack before use. For approximate charging times and recording/playback times with a fully charged battery pack, refer to the tables on pages 177-178. 1 Connect the power cord to the compact power adapter. 2 Plug the power cord into a power outlet. 3 Connect the compact power adapter to the camcorder’s DC IN terminal. 4 Attach the battery pack to the camcorder. Press the battery pack softly into the battery attachment unit and slide it up until it clicks in place. ON/OFF (CHG) (charge) indicator 5 Charging will start when the camcorder is turned off. • If the camcorder was on, the green ON/OFF (CHG) indicator will go out when you turn off the camcorder. After a moment, the ON/OFF (CHG) indicator will start flashing in red (battery pack charging). The red ON/ OFF (CHG) indicator will go out when the battery pack is fully charged. Preparations .. 27 POWER BATTERY RELEASE BATTERY RELEASE • If the indicator flashes quickly, refer to Troubleshooting ( 152). To remove the battery pack 1Slide in the direction of the arrow and hold it pressed down. 2 Slide the battery pack down and then pull it out. BATTERY RELEASE switch IMPORTANT • Turn off the camcorder before connecting or disconnecting the compact power adapter. After pressing to turn off the camcorder, important data is updated in the memory. Be sure to wait until the green ON/OFF (CHG) indicator goes out. • We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and 86 °F). Outside the temperature range of 0 °C to 40 °C (32 °F to 104 °F), charging will not start. • Do not connect to the camcorder’s DC IN terminal or to the compact power adapter any electrical equipment that is not expressly recommended for use with this camcorder. • To prevent equipment breakdowns and excessive heating, do not connect the supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc. NOTES • The battery pack will be charged only when the camcorder is off. • If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed. • Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day before, to ensure a full charge. 28 • Preparations • We recommend that you pre...