Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: FUNAI Dateigröße: 1.07 mb Dateiname: Unterrichtssprache:

“AV2” appears on the TV screen. If you use the AV1 (TV) socket, press CHANNEL (K/L) or enter “001” with the number buttons. “AV1” appears on the TV screen. Euro Scart cables are obtainable at your dealer. RF OUT AERIAL AV2(DECODER) to 21-Pin Scart socket Decoder (Not supplied) (TV) to RF OUT socket Scart socket to 21-Pin to aerial 5 EN HM210BD(EN).fm Page 6 Thursday, March 2, 2006 6:07 PM Initial Settings Video Channel Setting Video channel setting will be necessary, if your VCR is connected to the TV via the RF cable. • Use the remote control for this procedure. 1) Insert a pre-recorded tape into the VCR. The VCR will turn on and start playback automatically. If playback does not start, press PLAY/K. 2) Select and adjust your TV to channel 35. •If the playback picture appears on the TV screen, continue with step 8). •If channel 35 is set for broadcasting, or interference lines appear on the picture, the RF converter must be set to a different channel between CH22 and CH69. Continue with step 3). 3) Press MENU. 4) Press PLAY/K or STOP/L repeatedly to select to “INITIAL”. Then, press F.FWD/B. 5) Press PLAY/K or STOP/L repeatedly to select to “RF OUT”. Then, press F.FWD/B. The RF OUT CH menu will appear. 6) Press PLAY/K or STOP/L to select a channel which is not used for broadcasted between channel 22 and channel 69 in your area, then press F.FWD/B. 7) Press MENU to exit. Set the TV channel to the RF OUT CHANNEL which was selected on the VCR. A picture from the VCR will appear on the TV screen. If a picture does not appear, repeat steps 3) to 7) using a different channel which is not used for broadcast. 8) Press STOP/L to stop the tape. Note: You may also access the RF OUT CH menu by pressing and holding MENU on the remote control for 3 seconds during power off until the RF OUT CH menu appears. MENU TIMER SET UP INITIAL RF OUT CH 35 INITIAL CH TUNING CLOCK RF OUT Setting the Clock This VCR incorporates a 24-hour clock. The clock must be set for the Timer Recording function to operate correctly. • Use the remote control for this procedure. 1) Press MENU. 2) Press PLAY/K or STOP/L to select “INITIAL”, then press F.FWD/B. 3) Press PLAY/K or STOP/L to select “CLOCK”, then press F.FWD/B. 4) (31B-254 and 31B-454 only) Press PLAY/K or STOP/L to select “MANUAL” or “AUTO”, then press F.FWD/B. •If you select “MANUAL”, continue with step 5). •If you select “AUTO”, Auto Clock Setting becomes “ON”. Press FUNCTION. The clock will appear on the TV screen when you turn on the VCR again. 5) Press PLAY/K or STOP/L until the relevant year appears, then press F.FWD/B. 6) Press PLAY/K or STOP/L until the relevant month appears, then press F.FWD/B. 7) Press PLAY/K or STOP/L until the relevant day appears, then press F.FWD/B. 8) Press PLAY/K or STOP/L until the relevant hour appears, then press F.FWD/B. 9) Press PLAY/K or STOP/L until the relevant minute appears. 10)Press MENU to start the clock. Note: •Press REW/s to go one step back from the current step during steps 5) to 9). • Although seconds are not displayed, they begin counting from 00 when you exit by pressing MENU. Use this feature to synchronize the clock with the correct time. • If the VCR is unplugged or if there is a power failure for more than 30 seconds, you may have to reset the clock. [AUTO CLOCK] (31B-254 and 31B-454 only) • Channel Presetting must be set before the Auto Clock is set. • To set the clock automatically, the channel assigned to position 01 must have the PDC signal. • The clock cannot be set automatically if you are not receiving a channel that carries a time signal in your area. In this case, set the clock manually. • Once the auto clock setting is performed, the VCR will correct the current time by receiving PDC broadcasts whenever you turn off the VCR. • The VCR will correct the current time automatically at 8:00, if the VCR power is turned off. • Between 23:00~1:00, the AUTO CLOCK function does not work even if the VCR power is turned off. MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK RF OUT CLOCK YEAR 2 0 0 6 MONTH 0 1 DAY 0 4 WE HOUR _ _ MINUTE _ _ 6 EN HM210BD(EN).fm Page 7 Thursday, March 2, 2006 6:07 PM Channel Presetting Tuning of broadcast channels not already preset in the VCR can be performed in two ways. Automatic Channel Preset • By “AUTOMATICALLY” tuning channels and placing them in sequential order in the VCR’s memory i.e. the first channel found will be memorized into the VCR’s channel position 1, the second channel found will be memorized into the VCR’s channel position 2 and so on. • Execution of the “Automatic” channel presetting cancels all the preset channels. DO NOT use this feature if you intend to use some of the pre-tuned channels. Use the “Manual” channel presetting function to tune in the additional channels you require. Manual Channel Preset • Each channel is tuned manually and individually. Follow the steps laid out in the “Manual Channel Preset” section. Before you preset Channel... • It is necessary to set the vid...

Herunterladen

Geben Sie zwei Ziffern: