Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Oscillation Knob located on back of fan, on Perilla para oscilacion ubicada en la parte de en la parte de arriba de la caja del motor Bouton d’oscillation situe au dos du ventilateur, sur le boitier du moteur. 3. Base Base Socle 4. Rubber Feet Pies de goma Pieds en caoutchouc 5. Push-Button Switches Interruptores con boton a presion Boutons 6. Tabs Lenguetas Languettes 7. Metal Mesh Grilles Parrillas de malla metalica Grilles en maillees metalliques 8. Fan Blades Paletas Pales Power Supply Cord with Polarized Plug (not shown) Cable con enchufe polarizado (no ilustrado) Fil electrique avec fiche polarisee (non montre) LINE CORD SAFETY TIPS 1. Never pull or yank on the cord or the appliance. 2. To insert plug, grasp it firmly and guide it into outlet. 3. To disconnect appliance, grasp plug and remove it from outlet. 4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found, this indicates that the appliance should be serviced and the line cord replaced. 5. Never wrap the cord tightly around the appliance, as this could place undue stress on the cord where it enters the appliance and cause it to fray and break. DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY DAMAGE, OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS WORKING ENTIRELY. IMPORTANT: During the first few minutes of initial use, a slight odor may be noticeable. This is normal and will quickly disappear. HOW TO USE This appliance is for household use and may be plugged into a standard electrical outlet. ASSEMBLY INSTRUCTIONS 1. Place fan base on firm, stable surface such as a table or countertop. 2. Mount the rear grille to the motor housing by matching the round holes in the rear grille (two at the top and one at the bottom) to the round pins on the front of the motor housing. Push in firmly until the pins protrude through the holes. 3. Secure the rear grille to the motor housing by placing the plastic collar over the thread hub around the motor shaft and turning collar clockwise to tighten. 4. Push blade into the shaft pin firmly in place until it cannot be pulled out. Secure blade with cap, turning counterclockwise to tighten. 5. Please refer to the enclosed instruction sheet for details on how to assemble the front grille. OPERATING INSTRUCTIONS 1. Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord. 2. Before plugging in, adjust the direction of the airflow by firmly holding the base with one hand and pushing the fan grille back to tilt up or by pushing it forward to tilt down. 3. To make the fan oscillate, push down on the oscillating knob located on the top of the motor housing. To stop the fan from oscillating, pull up on the oscillation knob. 4. Plug fan into an electrical outlet. 5. Choose speed desired by depressing one of the buttons. CARE AND CLEANING This appliance requires little maintenance and contains no user serviceable parts. Do not try to fix it yourself. Refer it to qualified service personnel if servicing is needed. The fan is permanently lubricated and will not require additional lubrication for the life of the fan. TO CLEAN: Before cleaning, turn fan off and unplug from electrical outlet. Wipe off excess dust with a lint-free cloth. To ensure adequate air circulation to the motor, keep vents located at the rear of the motor housing free from dust accumulation. A vacuum cleaner hose can be used to clean these vents. Do not immerse fan in water or any other liquid. Disassemble grilles and blade. Grilles and blade may be cleaned with mild soap and water. Use a soft, slightly damp cloth to wipe the remaining fan parts. Do not allow water or any other liquid to get into the motor housing or base. Reassemble fan after grilles and blade have dried completely. Do not plug fan into electrical outlet until it has been fully reassembled. TO STORE: Make sure to disassemble and clean the fan before storing. Retain the original packaging for the purpose of storing the fan. Always store fan in a dry place. Never store it while it is still plugged in. Never wrap the cord tightly around the fan, and do not put any stress on the cord where it enters the fan housing, as it could cause the cord to fray and break. SUGERENCIAS PARA SEGURIDAD CON EL CABLE 1. Nunca hale ni tire del cable ni de la unidad. 2. Para conectar, sujete con firmeza el enchufe y guielo dentro de la toma de corriente. 3. Para desconectar, sujete el enchufe y retirelo de la toma de corriente. 4. Antes de usar el aparato, verifique que el cable no tenga cortaduras ni abrasiones. De ser asi, la unidad debe ser revisada y el cable debe ser reemplazado. Por favor devuelva la unidad a nuestro departamento de servicio o a un representante de servicio autorizado. 5. Nunca enrolle el cable de manera apretada en torno a la unidad, ya que el exceso de presion en las uniones del cable con la unidad o con el enchufe pueden raerlo o romperlo. NO OPERE LA UNIDAD SI EL CABLE PRESENTA CUALQUIER DANO, SI LA UNIDAD FUNCIONA DE MANER...