Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions. A clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. The hood can be installed above these heights but for optimum performance it should be installed at the distances quoted for the appropriate heat source. This appliance can be used in either extraction mode (ducting) or recycling mode (filtering). The hood is supplied suitable for recirculation with the charcoal filters fitted. When used in the extraction mode (ducting) the charcoal filters are not required and must be removed and destroyed. Hob A: Built-in Electric Hob: 650mm clearance B: Built-in Gas hob: 700mm clearance C: Slot-in Electric Cooker: 685mm clearance D: Slot-in Gas Cooker: 787mm clearance 13 Fitting the Wall Brackets INSTALLING THE COOKER HOOD INSTALLING THE COOKER HOOD Wall marking: • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. • Draw a horizontal line at 650 mm above the hob. • Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. • Mark the wall at the centres of the holes in the bracket. • Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. • Mark the wall at the centres of the holes in the bracket. • Mark a reference point as indicated at 116 mm from the vertical reference line and 310 mm above the horizontal reference line. • Repeat this operation on the other side. • Drill o 8 mm holes at all the centre points marked. • Insert the wall plugs (not supplied) in the holes. • Fix the lower bracket 7.2.1 using the two screws (not supplied). • Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using the two screws (not supplied). • Insert the two screws 12a (not supplied) supplied in the hood body fixing holes, leaving a gap of 5-6 mm between the wall and the head of the screw. Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). 14 Fitting the Hood Body Before starting to fi x the hood body, tighten the two screws Vr located on the top of the hood body. Hook the hood body onto the two screws item 12a (not supplied). Fully tighten the screws item 12a. Using a screw driver and spirit level, adjust the screws item Vr until the hood body is level. Extraction The cooker hood is more effective when used in the extraction mode (ducted to the outside). INSTALLING THE COOKER HOOD Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of O125mm (5”) or O150mm (6”). The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. When the cooker hood is ducted to the outside the charcoal filter must be removed. Recirculation The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. To assemble the recirculation duct, place the recirculation outlet connection item 15 into the support item 7.3. Insert the extension ducts item 14.1 into either side of the recirculation outlet item 15 ensuring the connections are vertically and horizontally aligned with the outlets in the chimney. Connect the recirculation oulet item 15 to the outlet on top of the hood body using either a piece of O125mm or O150mm flexible or rigid pipe. Rigid pipe is strongly recommended and should be used where possible as this will ensure the best performance while lowering noise. 15 INSTALLING THE COOKER HOOD INSTALLING THE COOKER HOOD Extraction The charcoal filter is not required in this mode and should be removed. Ducting The ducting used must be O150mm (6ins), or O125mm (5ins) in diameter. If possible duct through the wall immediately above the hood body. For the best performance use t...