Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. 4. Install a roof or wall cap. Connect 6" round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. INSTALL MOUNTING BRACKETS 1. Construct wood wall framing that is flush with interior surface of wall studs. Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting brackets to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mounting brackets to framing using dimensions shown. INSTALL THE HOOD 1. Hang the hood from the brackets through the rectangular cut-outs on the back of the hood. Cut-outs are larger than the brackets to allow for horizontal adjustment. The bottom of the hood should be 24" to 30" above the cooking surface. 2. Height adjustment screws provide vertical adjustment. 3. Depth adjustment screws provide horizontal adjustment. 4. Secure the hood with mounting screws (4.8x38mm). Use drywall anchors, provided, if wall studs or framing are not available. - 6 ROOF CAP 6” ROUND DUCT 24” TO 30” ABOVE COOKING SURFACE WALL CAP 6” ROUND ELBOW HOOD DECORATIVE FLUE 5 5/16” 5 5/16” 3/16” X X = min 30-3/8” -max 36-7/16” above cooktop FRAMING BEHIND DRYWALL 2 MOUNTING RECTANGULAR SCREWS CUTOUTS (4.8x38mm) FRAMING WALL MOUNTING BRACKETS DEPTH ADJUSTMENT SCREWS HEIGHT ADJUSTMENT SCREWS MOUNTING SCREWS (4.8x38mm) INSTALL DUCT COLLAR MOUNTING SCREWS (3.9x9.5mm) Attach the duct collar onto the hood; it must be attached by means of 2 mounting screws (3,9x9,5 mm Pan Head). WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. 1. Remove the wiring box cover. Remove a knockout from the wiring box. 2. Secure the conduit to the wiring box through a conduit connector. 3. Make electrical connections. Connect white to white, black to black and green to green. 4. Replace wiring box cover and screws. Make sure that wires are not pinched between cover and box. CONNECT DUCTWORK Ducted Configuration 1. Use (2) screws (4.8x38mm) and wall anchors to secure flue mounting bracket to the ceiling or wall as shown. 2. Use 6" round metal duct to connect the duct collar on the hood to the ductwork above. 3. Use duct tape to make all joints secure and air tight. 4. Connect the upper section of decorative flue to the bracket with screws provided (3.9x6mm). 5. Slide the lower section of decorative flue downward, until it fits properly around hood. 6. Secure decorative flue to hood with screws provided (3.9x6mm). FASTEN FLUE TO HOOD WITH SCREWS (3.9x6mm) WIRING BOX COVER DUCT COLLAR FLUE MOUNTING BRACKET DUCT TAPE DECORATIVE FLUE 6" ROUND METAL DUCT FASTEN FLUE TO BRACKET WITH SCREWS (3.9x6mm) - 7 MAINTENANCE Grease Filters The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. To take off the grease filters: at the handle, push the stop inwards and pull the filters downwards. Hood Cleaning GREASE FILTERS Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: . Hot water with soap or detergent is all that is usually needed. . Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. . For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth. . For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleaser and water. Rub lightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface. . DO NOT allow deposits to remain for long periods of time. . DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. . DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only. - 8 OPERATION Controls The hood is operated using the slide controls under the front edge of the hood. The light switch turns the halogen lights on and off. The blower on / off switch turns the blower on to the running speed set by the blower speed control. The blower must be turned on and off using this switch. The blower speed control changes the running speed of the blower (1-2-3). LIGHT BLOWER SWITCH ON / OFF B...