Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Emerson Dateigröße: 205.17 kb Dateiname: Unterrichtssprache:

Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 Five wire connectors (supplied) One wire stripper MATERIALS Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following size: WARNING ! Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 6). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician. Unpacking Instructions For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted. ! WARNING Do not install or use fan if any part is damaged or missing. Call Toll-Free: 1-800-654-3545 WARNING ! This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson. Substitution of parts or accessories not designated for use with this product by Emerson could result in personal injury or property damage. NOTE: Place the parts from the loose parts bags in small containers to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding. NOTE: Fan blades are ordered separately and are packaged in separate carton. LOOSE PARTS BAG BLADE FLANGES SWITCH HOUSING COVER HANGER BRACKET HANGER BALL/ DOWNROD ASSEMBLY CEILING COVER FAN MOTOR AND HOUSING ASSEMBLY MOTOR COVER 1. Open styrofoam unit containing fan. Remove top half of styrofoam unit. Remove parts and check to see that you have received the following: a. Fan motor and housing assembly b. One motor cover c. One ceiling cover d. Five blade flanges e. One hanger ball/downrod assembly f. One hanger bracket g. One switch housing cover h. One loose parts bag containing: 1. One setscrew 2. One setscrew wrench 3. Eleven 10-32 x 5/8" oval head screws 4. Two 1” threaded studs 5. Two 1-1/4” threaded studs 6. Four knurled knobs 7. Five wire connectors 8. Two 8-32 x 3/8" screws 9. One pull chain pendant and coupling 10. One hairpin clip 11. One clevis pin 12. Four lockwashers 13. Twenty-one 10-32 x 3/8" pan head screws 14. Twenty-one flat washers 3 Assembly Instructions 1. Remove the fan motor and housing assembly from styrofoam packaging and position it so that the top of the motor is facing you. 2. Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly and seat the downrod in the motor coupling (Figure 1). Figure 1 MOTOR LEADS (BLACK, WHITE, AND BLUE) MOTOR COUPLING FAN MOTOR AND HOUSING ASSEMBLY HANGER BALL/ DOWNROD ASSEMBLY WARNING ! It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 2) could result in the fan falling. 3. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 2). (Pin and clip are supplied in loose parts bag.) The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed. SETSCREW MOTOR COUPLING CLEVIS PIN HAIRPIN CLIP CONNECTED RED LEADS CONNECTED BROWN LEADS WHITE LEAD SETSCREW CLEVIS PIN MOTOR COUPLING DOWNROD HAIRPIN CLIP HANGER BALL Figure 2 4 4. Install the setscrew (supplied) in the motor coupling (Figure 2). While pulling up on the hanger ball, tighten the setscrew using the setscrew wrench (supplied). NOTE: The setscrew must be properly installed as described above, or fan wobble could result. 5.Remove the hanger ball by looseni...

Herunterladen

Geben Sie zwei Ziffern: