Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Emerson Dateigröße: 205.17 kb Dateiname: b3904c19-6f28-46ef-ba53-a822a6ec8d53.pdf Unterrichtssprache:

5 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is ground- ed, contact a licensed electrician for advice, as it must be grounded for safe operation. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 9). Securely connect wires with wire connector supplied. NOTE: CEILING COVER OMITTED FOR CLARITY. LISTED WIRE CONNECTOR (3) GREEN WIRE (GROUND) FROMHANGER BRACKET GREEN WIRE (GROUND) FROMHANGER BALL WHITE SUPPLY (NEUTRAL) WHITE FAN WIRE BLACK SUPPLY (HOT) BLACK AND BLUE FAN WIRES Figure 9 SUPPLY GROUND WIRE NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner’s Manual for wiring. 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 9). Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using wire connector supplied (Figure 9). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box. WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. 3. Screw the two 1-1/4” threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 10). 4. Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 10). 5. Secure the ceiling cover in place by sliding lockwashers (supplied) over the threaded studs and installing the two knurled knobs (supplied). (Figure 10.) Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan switch. CEILING COVERLOCKWASHER THREADED STUD 1-1/4" KNURLED KNOB Figure 10 WARNING ! To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. Installing Fan Blades 1. Use four 10-32 x 3/8” pan head screws and flat washers (supplied) to secure the flange to the fan blade (ordered separately) (Figure 11). Repeat for the remaining four blades. 10-32 x 3/8" PAN HEAD SCREW FLAT WASHER FAN BLADE BLADE FLANGE Figure 11 6 2. Use the 10 round recessed holes in the motor hub marked with "5" and install the five blade assemblies in accordance with Step 3. 3. Attach one blade assembly to the motor hub using two 10-32 x 5/8" oval head screws (supplied) (Figure 12). Do not tighten completely at this time. Install four remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. This completes the blade installation. MOTOR HUB 10-32 x 5/8" OVAL HEAD SCREW (2 Per Blade Assembly)Figure 12 WARNING ! To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades. 4. Slip the pull chain through the bushing in the switch housing cover. Position the switch housing cover on the switch housing and secure using two 8-32 x 3/8” screws (supplied) (Figure 13). Secure the pendant (supplied) to the pull chain using the connector (supplied). SWITCH HOUSING COVER PULL CHAIN 8-32 x 3/8" SCREW Figure 13 Using Your Ceiling Fan 1. Restore ele...

Herunterladen

Geben Sie zwei Ziffern: