Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Applied Energy Products Dateigröße: 814.4 kb Dateiname: Unterrichtssprache:

6. Go outside and cut a hole in the outer wall, repeating the process described above. 7. Cut ducting to the correct length if required. 8. Fit the ducting. Ensure that the duct slopes down away from the fan to allow drainage of any incoming rain water to the outside. 9. Make good the hole around the ducting. Allow the mortar to set before continuing with the fan installation. If installing in a window or panel 1. Cut a hole, 125mm in diameter or if installing in a window, obtain a ready cut pane. 2. The centre of the hole should be at least 110mm away from the edge of the panel or pane of glass. If installing in a ventilation shaft 1. Check there are no buried pipes or cables in the ventilation shaft. If in doubt seek professional advice. 2. Cut a hole 110mm in diameter, in the side of the shaft. If installing in a ceiling 1. Check there are no buried pipes or cables in the ceiling above the fan location. If in doubt seek professional advise 2. Cut a hole 115mm diameter. Preparing the fan for installation Remove the front cover by pressing the release catches located on the sides of the unit with a 3mm screwdriver, whilst pulling the front cover forward (fig E). Mount the fan in the hole If working above ground floor level, appropriate safety precautions must be observed. If installing in a wall, ceiling or vent Mark the position of the back plate (fig A) 1. Hold the backplate so that the terminal block faces you in the top left hand corner and the lip points towards the hole. 2. Carefully insert the lip into the wall duct/ceiling or vent shaft. 3. Adjust the position of the back plate until it is level. 4. Mark on the wall/ceiling or vent shaft the positions of the three fixing holes in the back plate. 5. Remove the back plate from the ducting. 6. Drill screw holes in these positions if necessary, and fit wall plugs if necessary. Mount the back plate (fig B) 1a.If installing in a vent, an XXVK4 Vent Kit is required. Follow instructions provided. 1b.If installing in a ceiling, an XXCK4 Ceiling Kit and termination ancillaries are required. Follow instructions provided. 2. If wiring the fan from behind, remove knockout. Feed the mains cable entry hole in the backplate to the terminals (Fig C). 3. If wiring from above, leave the cable free to be fitted into labyrinth. 4. Insert the lip of the back plate into the wall duct/ceiling or vent shaft as before. 5. Fasten the back plate to the wall/ceiling or vent shaft using appropriate fasteners. If using screws, do not overtighten. 6. If installing in a wall, a CFWG100 Wall Grille is required. Follow instructions provided. If installing in a window or panel 1. If installing in a window or panel no more than 9mm thick, a XXGK4 Glass Kit is required. Follow instructions supplied. Wire the electrical connections • Make sure the mains supply is isolated. • All wiring and installation must be supervised by a qualified electrician. 1. Wire the fan as shown in fig D. Check fan model for correct diagram. Feed the cable between the two raised pegs, if wiring from above, and through labyrinth to terminal block. 2. Switch off the mains electrical supply and remove fuses. 3. Connect the cable from the isolating switch to the electrical supply wiring. • For fixed wiring circuits the protective fuse for the appliance must not exceed 5A. All Fans • If wiring from above, cut out the cable entry slot marked on top of the front cover. • Fit the front cover by aligning it square to the duct and pushing it onto the backplate until the release catches snap into the slots on the front cover. • Refit the fuses and switch on the mains supply. Operating the fan XX100 only • Operate the fan using the on/off switch. Repeat to turn off. XX100P only • Operate the fan by pulling and releasing the cord. Repeat to turn off. XX100T only • Operate the fan using an on/off switch. When the switch is turned off, the fan continues to operate for the set time delay. ...

Herunterladen

Geben Sie zwei Ziffern: